37569139
annual rates for maintenance and repair & minor original civil works items for various buildings under navsari ( r&b ) division, navsari excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 meter lead. ( a ) loose or soft soil, excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 meter lead. ( a ) loose or soft soil, excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 meter lead. ( a ) loose or soft soil, filling available excavated earth ( excluding rock ) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering., filling in plinth with sand under floors including watering ramming, consolidating and dressing complete, filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including watering, ramming and consolidating etc. complete., filling in foundation and plinth with brick bats chhara in layers of 20cm. thickness including watering, remming and consolidating etc. complete., boring holes 3.5 m deep in ordinary soil ( for cast in situ piles ) and getting out the soil and disposal of the surplus excavated soil as directed within a lead of 50 meter for following diameter of pipes. ( i ) 200 mm, boring holes 3.5 m deep in ordinary soil ( for cast in situ piles ) and getting out the soil and disposal of the surplus excavated soil as directed within a lead of 50 meter for following diameter of pipes. ( ii ) 250 mm, boring holes 3.5 m deep in ordinary soil ( for cast in situ piles ) and getting out the soil and disposal of the surplus excavated soil as directed within a lead of 50 meter for following diameter of pipes. ( iii ) 300 mm, extra for under reaming inside the bore holes for under reamed piles of following diameter. ( i ) 200 mm, extra for under reaming inside the bore holes for under reamed piles of following diameter. ( ii ) 250 mm, extra for under reaming inside the bore holes for under reamed piles of following diameter. ( iii ) 300 mm, add to or deduct from the rate for bore holes of 3.5 m depth, if bore holes are made deeper or shallower than 3.5m. for piles of following diameter. ( i ) 200 mm, add to or deduct from the rate for bore holes of 3.5 m depth, if bore holes are made deeper or shallower than 3.5m. for piles of following diameter. ( ii ) 250 mm, add to or deduct from the rate for bore holes of 3.5 m depth, if bore holes are made deeper or shallower than 3.5m. for piles of following diameter. ( iii ) 300 mm, providing and laying cement concrete 1:4:8 ( 1 cement : 4 coarse sand : 8 crushed stone aggregates 40 mm nominal size ) and curing complete excluding cost of formwork in ( a ) foundation and plinth, providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 crushed stone aggregates 20 mm nominal size ) and curing complete including cost of formwork in ( a ) wall caps / coping, providing and laying cement concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 crushed stone aggregates 40 mm nominal size ) and curing complete excluding cost of formwork in ( a ) foundation and plinth, providing and laying cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork in ( a ) foundation and plinth, providing and laying cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork in ( b ) independent piers, columns, and pillars, upto floor two level, providing and laying cement concrete work 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( a ) foundations, footings, base or columns and mass concrete, providing and laying cement concrete work 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( b ) slabs, landing, shelves, balconis , lintels, beams, girders and cantilever upto floor two level., providing and laying cement concrete work 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( d ) columns, pillars posts and struts upto floor two level., providing and laying cement concrete work 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( e ) staircases excluding landing upto floor two level, providing and laying cement concrete work 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( k ) vertical and horizontial its upto floor two level., providing and laying cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) for reinforced concrete chhajjas not exceeding 10cm. thickness upto floor two level including finishing the exposed surfaces with cement mortar 1:3 ( 1 cement, 3 fine sand ) to give a smooth and even surface centering and formwork and curing complete excluding cost of reinforcement., providing is mark tmt bar fe 415 reinforcement for r.c.c. work including bending, binding and placing in position complete upto floor two level, extra for additional lift of concrete for all r.c.c. work above floor two level excluding cost of reinforcment, extra for additional lift of reinforcing steel for all r.c.c. work above floor two level., deduct for omiting in r.c.c. work smooth finishing of the exposed surface with cement mortar 1:3 ( 1 cement : 3 fine sand ) , providing throating or plaster drip and moulding to r.c.c. chhajja., providing upto floor two level precast cement concrete jali or grill 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size ) reinforced with 1.6 mm dia. mild steel wire including roughening, cleaning, fixing and finishing in cement mortar 1:3 and curing complete. ( a ) 50mm thick, providing upto floor two level precast cement concrete jali or grill 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size ) reinforced with 1.6 mm dia. mild steel wire including roughening, cleaning, fixing and finishing in cement mortar 1:3 and curing complete. ( d ) 75mm thick, providing upto floor two level precast cement concrete jali or grill 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size ) reinforced with 1.6 mm dia. mild steel wire including roughening, cleaning, fixing and finishing in cement mortar 1:3 and curing complete. ( e ) 100mm thick, extra for additional lift for providing and fixing in position precast r.c.c. units above floor two level, extra for providing and mixing water proofing material in cement concrete in mix proportion recommended by the manufacturers., providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( a ) foundations, footings, base of columns and mass concrete, providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( b ) walls, from top of foundation level upto floor two level, providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( c ) slabs, landing, shelves, balconies, lintels, beams, girders and cantilever upto floor two level, providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( d ) columns, pillars posts and struts upto floor two level., providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( e ) staircases excluding landing upto floor two level, providing and laying controlled cement concrete m.150 for curing complete excluding cost of formwork and reinforcement for reinforced concrete work in ( k ) vertical and horizontial its upto floor two level., providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( a ) foundations, footings, base of columns and mass concrete, providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( b ) walls, from top of foundation level upto floor two level, providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( c ) slabs, landing, shelves, balconies lintels, beams, girders and cantilever upto floor two level., providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( d ) columns, pillars posts and struts upto floor two level., providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( e ) staircases excluding landing upto floor two level, providing and laying controlled cement concrete m.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( k ) vertical and horizontial its upto floor two level., providing and laying controlled cement concrete m.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( a ) foundations, footings, base of columns and mass concrete., providing and laying controlled cement concrete m.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( b ) walls, from top of foundation level upto floor two level, providing and laying controlled cement concrete m.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( c ) slabs, landing, shelves, balconies, lintels, beams, girders and cantilever upto floor two level., providing and laying controlled cement concrete m.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in ( d ) columns, pillars posts and struts, upto floor two level., providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for r.c.c work in ( iii ) slabs having more than 10 cm and upto 13 cm. thickness, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for r.c.c work in ( iv ) slabs having more than 13 cm and upto 15 cm.thickness, providing and laying controlled cement concrete m.150 and finishing smooth with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for r.c.c work in ( iii ) slabs having more than 10 cm and upto 13 cm. thickness, providing and laying controlled cement concrete m.150 and finishing smooth with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for r.c.c work in ( iv ) slabs having more than 13 cm and upto 15 cm.thickness, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) for r.c.c lintel including finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement., providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( a ) beams : ( i ) having cross sectional area 0.05 to 0.08 sq.m, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( a ) beams : ( ii ) having cross sectional area more than 0.08sq.m and upto 0.12 sq.m, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( a ) beams : ( iii ) having cross sectional area more than 0.12sq.m and upto 0.18 sq.m, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( b ) columns: ( i ) having cross sectional area 0.05 to 0.08 sq.m, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( b ) columns: ( ii ) having cross sectional area more than 0.08 sq.m and upto 0.18 sq.m, providing and laying ordinary cement concrete 1:2:4 ( 1 cement 2 coarse sand : 4 graded stone aggregates 20 mm nominal size ) and finishing smooth with, curing etc. complete including the cost of formwork but excluding the cost of reinforcement for r.c.c work in ( b ) columns: ( iii ) having cross sectional area more than 0.12sq.m and upto 0.18 sq.m, providing and applying anticarrasive treatment with polymer base materials to the steel rainfarcement including descaling the dust and applying the preventive coating of approved make ( for the r.c.c. structures near coastal area only ) etc complete., providing and fixing in expansion joint 100 mm thick sil flex ( capcell hd 100 ) expansion joint board of best quality and approved make including cutting to required size and shape at all levels etc. complete as directed., providing and laying and fixing 50 mm thick expansion joint by hydro cell semi rigid uv resistance with high performance laminated closed cell polythene foam joint filler in sheet foam as directed, etc. complete., providing and laying and fixing 25 mm thick expansion joint by hydro cell semi rigid uv resistance with high performance laminated closed cell polythene foam joint filler in sheet foam as directed, etc. complete., applying and providing expansion joint sealing system on 100 mm vide joint including cleaning of exansion joint by mechanical means provision of adhesive and flexible membrane with required bond length as per menufracturer specification and 4mm thick alluminium strip covering with one side sloted and bolted with suitable system, inclusive of all manpower, machinery and material as per specification and as directed., providing and filling the expansion joint by thioflex 600 polymer or equivalent confirm to bs 4254 1983 as per required shade and manufactured specifi cation by making groove of 50 mm x 12.5 mm lather by cutting or by repairing groove and removing mortar drop or any other foreign materials including applying primer and filling required size ( oversize of joint pu foam etc. complete., providing and filling the expansion joint by thioflex 600 polymer or equivalent confirm to bs 4254 1983 as per required shade and manufactured specifi cation by making groove of 25 mm x 12.5 mm lather by cutting or by repairing groove and removing mortar drop or any other foreign materials including applying primer and filling required size ( oversize of joint pu foam etc. complete., providing and fixing 25 cm wide & 3mm thick exterior composite panel on existing expansion joint horizontally & vertically with all material, hardware, acessories & fittings etc completed., providing and laying in position ready mixed m 150 grade concrete for reinforced cement conctere work , using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of r.m.c. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. without fly ash ( min cement level as per latest is 456 shall be maintained ) ( cement level 320 kg ) , providing and laying in position ready mixed m 200 grade concrete for reinforced cement conctere work , using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of r.m.c. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. without fly ash ( min cement level as per latest is 456 shall be maintained ) ( cement level 400 kg ) , providing and laying in position ready mixed m 250 grade concrete for reinforced cement conctere work , using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of r.m.c. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. without fly ash ( min cement level as per latest is 456 shall be maintained ) ( cement level 450 kg ) , providing and laying in position ready mixed m 300 grade concrete for reinforced cement conctere work , using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of r.m.c. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. without fly ash ( min cement level as per latest is 456 shall be maintained ) ( cement level 475 kg ) , providing and laying in position ready mixed m 350 grade concrete for reinforced cement conctere work , using cement content as per approved design mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of r.m.c. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. without fly ash ( min cement level as per latest is 456 shall be maintained ) ( cement level 500 kg ) , providing and applying anti carbonation, anti fading, mold resistant, heat insulating, and 100% acrylic breathable decorative external waterproof coating of approved shade having viscosity @ room temperature by ford cup no. b 4 ( dilute 2 parts of product with i part of water ) 18 to 30 sec. ph of 7.00 to 10.00 and sp. gravity @ room temperature 1.30+0.1, tested for carbon dioxide diffusion resistance properties for coating materials and coating systems for exterior masonry and concrete as per din en 1062 6 ( 2002 2010 ) by a nba grade "a" accredited institution., providing and fixing capcell hd 100 pre moulded compressible filler board in black colour confirming to mort&h specifications ( clause 1015 ) , having minimum density 95kg / cum.metre, non staining with less than 1% water absorption & compression recovery of 93% minimum as per specification for 12 mm wide expansion joint including cutting to required size and shape at all levels etc. complete as directed., providing and fixing capcell hd 100 pre moulded compressible filler board in black colour confirming to mort&h specifications ( clause 1015 ) , having minimum density 95kg / cum.metre, non staining with less than 1% water absorption & compression recovery of 93% minimum as per specification for 20 mm wide expansion joint including cutting to required size and shape at all levels etc. complete as directed., providing and fixing capcell hd 100 pre moulded compressible filler board in black colour confirming to mort&h specifications ( clause 1015 ) , having minimum density 95kg / cum.metre, non staining with less than 1% water absorption & compression recovery of 93% minimum as per specification for 40 mm wide expansion joint including cutting to required size and shape at all levels etc. complete as directed., providing and applying the elastomeric joint sealant two component, high performance polysulfide formulation conforming to bs:4254 and astm c 920 having weathering resistance to ultra violet rays and shall exhibit shore a hardness of 25 and have movement accommodation factor 25% including using of compatible primer of approved standard etc. complete. for 12 mm thick joint, providing and applying the elastomeric joint sealant two component, high performance polysulfide formulation conforming to bs:4254 and astm c 920 having weathering resistance to ultra violet rays and shall exhibit shore a hardness of 25 and have movement accommodation factor 25% including using of compatible primer of approved standard etc. complete. for 20 mm thick joint, brick work using common burnt clay building bricks having crushing strength not less than 35 kg. / sq.cm. in foundation and plinth in cement mortar 1:5. ( 1 cement : 5 fine sand ) ( b ) conventional, brick work using building bricks having crushing strength not less than 70 kg. / sq.cm. in foundation and plinth in cement mortar 1:5. ( 1 cement : 5 fine sand ) ( c ) fly ash bricks, brick work using common burnt clay building bricks having crushing strength not less than 35 kg. / sq.cm. in foundation and plinth in cement mortar 1:6 ( 1 cement : 6 fine sand ) ( b ) conventional, brick work using building bricks having crushing strength not less than 70 kg. / sq.cm. in foundation and plinth in cement mortar 1:6 ( 1 cement : 6 fine sand ) ( c ) fly ash bricks, brick work using common burnt clay building bricks having crushing strength not less than 35 kg. / sq.cm. in foundation and plinth in cement mortar 1:8 ( 1 cement : 8 fine sand ) ( b ) conventional, brick work using building bricks having crushing strength not less than 70 kg. / sq.cm. in foundation and plinth in cement mortar 1:8 ( 1 cement : 8 fine sand ) ( c ) fly ash bricks, brick work using common burnt clay building bricks having crushing strength not less than 35 kg. / sq.cm. in foundation and plinth in lime mortar 1:1.5 ( 1 lime putty :1.5 fine sand ) ( b ) conventional, brick work using building bricks having crushing strength not less than 70 kg. / sq.cm. in foundation and plinth in lime mortar 1:1.5 ( 1 lime putty :1.5 fine sand ) ( c ) fly ash bricks, brick work using common burnt clay building bricks having crushing strength not less than 35 kg. / sq.cm. in foundation and plinth in lime mortar 1: 2 ( 1 lime putty : 2 fine sand ) ( b ) conventional, brick work using building bricks having crushing strength not less than 70 kg. / sq.cm. in foundation and plinth in lime mortar 1: 2 ( 1 lime putty : 2 fine sand ) ( c ) fly ash bricks, extra for brick work in superstructure above plinth level upto floor two level ( b ) conventional, extra for brick work in superstructure above plinth level upto floor two level ( c ) fly ash bricks, extra for brick work in superstructure above floor two level item no. 1 ( 6.12 ) ( b ) conventional, extra for brick work in superstructure above floor two level item no. 1 ( 6.12 ) ( c ) fly ash bricks, extra for brick work in superstructure above floor two level item no. 2 ( 6.13 ) ( b ) conventional, extra for brick work in superstructure above floor two level item no. 2 ( 6.13 ) ( c ) fly ash bricks, extra for brick work in superstructure above floor two level item no. 3 ( b ) conventional, extra for brick work in superstructure above floor two level item no. 3 ( c ) fly ash bricks, extra for brick work in superstructure above floor two level item no. 4 ( b ) coventional, extra for brick work in superstructure above floor two level item no. 4 ( c ) fly ash bricks, ( i ) half brick masonry in common brunt clay building bricks having crushing strength not less than 35 kg / sq.cm. in cement mortar 1:4 ( 1 cement : 4 coarse sand ) in foundation and plinth ( b ) conventional, ( i ) half brick masonry in building bricks having crushing strength not less than 70 kg / sq.cm. in cement mortar 1:4 ( 1 cement : 4 coarse sand ) in foundation and plinth ( c ) fly ash bricks, ( ii ) half brick masonry in common brunt clay building bricks having crushing strength not less than 35 kg / sq.cm. in cement mortar 1:5 ( 1 cement : 5 coarse sand ) in foundation and plinth ( b ) conventional, ( ii ) half brick masonry in building bricks having crushing strength not less than 70 kg / sq.cm. in cement mortar 1:5 ( 1 cement : 5 coarse sand ) in foundation and plinth ( c ) fly ash bricks, ( iii ) half brick masonry in common brunt clay building bricks having crushing strength not less than 35 kg / sq.cm. in lime mortar 1:1.5 ( 1 lime : 1.5 coarse sand ) in foundation and plinth ( b ) conventional, ( iii ) half brick masonry in building bricks having crushing strength not less than 70 kg / sq.cm. in lime mortar 1:1.5 ( 1 lime : 1.5 coarse sand ) in foundation and plinth ( c ) fly ash bricks, half brick masonry in common brunt clay building bricks having crushing strength not less than 35 kg / sq.cm. in cement mortar 1:3 ( 1 cement : 3 coarse sand ) with 2 nos of 6mm mild steel round bars after every three course embedded in cement mortar in foundation and plinth ( b ) conventional, half brick masonry in building bricks having crushing strength not less than 70 kg / sq.cm. in cement mortar 1:3 ( 1 cement : 3 coarse sand ) with 2 nos of 6mm mild steel round bars after every three course embedded in cement mortar in foundation and plinth ( c ) fly ash bricks, extra for half brick masonry in superstructure above plinth level upto floor two level. ( b ) conventional, extra for half brick masonry in superstructure above plinth level upto floor two level. ( c ) fly ash bricks, extra for half brick masonry in superstructure above floor two level. ( b ) conventional, extra for half brick masonry in superstructure above floor two level. ( c ) fly ash bricks, masonary work using aerated light weight concrete block having crushing strength not less than 35 kg / sqcm for super structure above plinth level upto floor two level in cement mortar 1:5 ( 1 cement : 5 fine sand ) complete as per technical specification, providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( a ) foundations footings bases of columns etc. and mass concrete., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( b ) flat surfaces such as soffits of supspened floors slabs landings and the like. ( 1 ) floors etc. upto 200 mm in thickness., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( b ) flat surfaces such as soffits of suspended floor roof slabs landings and the like. ( 2 ) floors etc. above 200mm in thickness., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( c ) vertical surface such as walls ( any thickness ) partitions and the like including attached buttresses & string course & the like., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( g ) columns pillarsposts and struts. ( 1 ) square rectangular polygonal in plan., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( g ) columns pillarsposts and struts. ( 2 ) circular or curved in plan., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( h ) ( 1 ) sides and soffits of beams beam haunchings cantilevers girders bressumers and lintels not exceeding 1 m. in depth., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( h ) ( 2 ) sides and soffits of beams beam haunchings canti levers girders bressumers and lintels exceeding 1m.in depth., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( i ) edges of slabs and breaks in floors and walls., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( k ) small surfaceassuch as cantiever brackets and ends of steps caps and basses to pilasters and columns and the like., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( l ) chullah hoods, weather shades chhajjas corbels etc. including edges., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( m ) staircase with sloping or stepped soffits including risers and stringers excluding landing., providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m. and removal of the same for in situ reinforced concrete and plain concrete work in. ( q ) vertical fins and vertical sun breakers., extra for additional height of propping and centering where the height of propping and centering exceeds 4 .o m between supporting floor to ceiling including temporary brick or stone pillars for supporting as required. ( i ) height more than 4.0 m.and upto 5.0 m., extra for additional height of propping and centering where the height of propping and centering exceeds 4 .o m between supporting floor to ceiling including temporary brick or stone pillars for supporting as required. ( ii ) height more than 5.0 m.and upto 6.0 m., extra for additional height of propping and centering where the height of propping and centering exceeds 4 .o m between supporting floor to ceiling including temporary brick or stone pillars for supporting as required. ( iii ) height more than 6.0 m. and upto 7.0 m, providing wood work in frames of doors, windows cleare story windows and othersimilar works wrought, framede and fixed in position. ( a ) indian teak wood, providing wood work in trusses, purling, rafter, post, post plates, wall plates and the like wrought framed, hoisted and fixed in position, providing wood work in frames of false ceiling, partitions etc sawn and put up in position. ( a ) indian teak wood, providing and fixing 35 mm thick shutters for doors, windows and clear story windows including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood ( 1 ) fully panelled, providing and fixing 35 mm thick shutters for doors, windows and clear story windows including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood ( ii ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clear story windows including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood ( iii ) partly panelled and partly glazed., providing and fixing 35 mm thick shutters for doors, windows and clearstory windows including blackenamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( i ) fully panelled., providing and fixing 35 mm thick shutters for doors, windows and clearstory windows including blackenamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( ii ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clearstory windows including blackenamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( iii ) partly panelled and partly glazed., providing and fixing 25 mm thick shutters for cupboards etc. including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood. ( i ) fully panelled., providing and fixing 25 mm thick shutters for cupboards etc. including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood. ( ii ) fully glazed., providing and fixing 25 mm thick shutters for cupboards etc. including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood. ( iii ) partly panelled and partly glazed., providing and fixing 25 mm thick shutters for cupboards etc. including black enamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( i ) fully panelled., providing and fixing 25 mm thick shutters for cupboards etc. including black enamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( ii ) fully glazed., providing and fixing 25 mm thick shutters for cupboards etc. including black enamelled m.s. butt hinges with necessary screws. ( a ) indian teak wood. ( iii ) partly panelled and partly glazed., add extra for providing and fixing 40 mm thick shutters instead of 35 mm thick shutters., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including anodised alluminium but hinges with necessary screws and indian teak wood shutters with. ( a ) plywood sheet panels., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including anodised alluminium but hinges with necessary screws and indian teak wood shutters with. ( b ) particle board panels, providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including anodised alluminium but hinges with necessary screws and indian teak wood shutters with. ( c ) hard board panels., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including anodised alluminium but hinges with necessary screws and indian teak wood shutters with. ( d ) asbestos sheet panels., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including black enamelled m.s. but hinges with necessary screws. ( a ) plywood sheet panels., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including black enamelled m.s. but hinges with necessary screws. ( b ) particle board panels, providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including black enamelled m.s. but hinges with necessary screws. ( c ) hard board panels., providing and fixing 35 mm thick panelled , glazed or panelled and glazed shutters, for doors windows and clearstory windows including black enamelled m.s. but hinges with necessary screws . ( d ) asbestos sheet panels., provoding and fixing flush door shutters, solid core construction with frame of first class hardwood with cross board and face veneer or plywood face panels, including anodised alluminium butt hinges with necessary screws. ( b ) non decorative type and block board core anodised alluminium butt hinges in flush door shutters ( 2 ) 35 mm thick., extra for using bright finished m.s. piano hinges of ( a ) nickel plated piano hinges., extra for providing vision panel not exceeding 0.1 sq.m. in all types of flush doors. ( a ) rectangular or square., providing and fixing 30 mm wire gauge shutters using galvanised m.s. wire of i.s. gauge designation of 85 g. with wire of 0.56 mm dia, for doors, windows and clearstory windows including anodised alluminium butt hinges with necessary screws. ( a ) indian teak wood., providing and fixing 30 mm wire gauge shutters using galvanised m.s. wire of i.s. gauge designation of 85 g. with wire of 0.56 mm dia, for doors, windows and clearstory windows including bright finished or / and black enamellede m.s. butt hinges with necessary mango wood or equivalent quality., extra for providing and fixing galvanised m.s wire gauge of i.s. gauge designation 140 g, to 000 rs. windows and cleastory windows with wire of dia 0.71 mm instead of i, s, gauge designation 85 g.with wire of dia.0.56 mm., providing and fixing 12 mm thick and 100mm wide pelmet of flat pressed 3 layer neneed particle board solid core with 25 mm diametre alluminium curtain road and brackets including fixing with 25mm x 3mm m.s flat 10cm, long and plugs etc.complete., providing and fixing 40mm panelled, glazed or panelled and glazed partitions fixed to frames with iron scews etc. complete with indian teak wood ( frames tobe paid separately ) , providing and fixing decorative plywood 4mm thick in partitions including fixing to frames with screws etc, complete with 50mm x 12mm teak wood beading ( frames tobe paid separately ) , providing and fixing plain asbestos cement sheet 6mm thick in partitions including fixing to fames with screws etc, complete with 50mm x 12mm deodar wood beading ( frames tobe paid separately ) , providing and fixing in partitions 4mm thick medium hard board of approved quality including fixing to fames with screws etc, complete with 50mm x 12mm teak wood beading ( frames tobe paid separately ) , 25 mm thick wooden shelves supported on 40 x 40mm x 6 mm t or l iron brackets fixed at suitable distances but not exceeding 75 cm. apart with mango wood or equivalent quality., 40 mm thick wooden shelves supported on 40 x 40mm x 6 mm t or l iron brackets fixed at suitable distances not exceeding 75 cm. apart with mango wood or equivalent quality., providing and fixing m.s. round or square bars with m.s.flats at required spacing in wooden frames of windows and clerestory windows., providing and fixing m.s. grills of required pattern to wooden frames of windows etc. with m.s. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws ( a ) plain grill., providing and fixing m.s. grills of required pattern to wooden frames of windows etc. with m.s. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws. ( b ) ornamental grill, providing and fixing hard drawn steel wire fabric 75mm x 25mm mesh or weight not less than 7.75 kg. per sq.m. to window frames etc. including 60 x 20mm beading of teak wood., providing and fixing fly proof galvanised m.s. wire gauge of i.s.l gauge designation 85 g. with wire of dia.0.56 mm to windows and celevating windows including 60 x 20mm beading of teak wood., providing and fixing first class indian teak wood 75mm x 60mm moulded hand rails in straight lengths complete., ( i ) providing and fixing glazed louvered glass windows and ventilators with teak wood frame 10cm. x 7cm. size including 3 coats of oil painting to wood work etc.complete., ( ii ) providing and fixing glazed louvered glass windows and ventilators with teak wood frame 10cm. x 7cm. size including 3 coats of oil painting to wood work etc.complete. with wooden louvers plank 12mm thick, providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( i ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( ii ) fully panelled., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( iii ) partly panelled and partly glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including black enamelled iron oxidixed fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( i ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including black enamelled iron oxidixed fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( ii ) fully panelled., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 10 cm x 7 cm. size including black enamelled iron oxidixed fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( iii ) partly panelled and partly glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( i ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( ii ) fully panelled., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( iii ) partly panelled and partly glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including black enamelled iron oxidized fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( i ) fully glazed., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including black enamelled iron oxidized fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( ii ) fully panelled., providing and fixing 35 mm thick shutters for doors, windows and clerestory windows including indian teak wood frames 12 cm x 7 cm. size including black enamelled iron oxidized fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. ( iii ) partly panelled and partly glazed., add extra for providing and fixing 40mm thick shutters instead of 35 mm thick shutters including oil paining etc. complete., deduct for providing and fixing 25mm thick shutters instead of 35 mm thick shutters including oil paining etc. complete., providing and fixing frp frame size 125x65 mm and 35mm thick frp shutter with wood grain raised panneled design finish shutter having extra reinforcement on sides & edges in gel coat finish. the core of the shutter & frame is to be filed up with injected polyurethene foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with fastener sleeve & alluminium fixtures & fastenings., providing and fixing frp frame size 100x50 mm and 28mm thick frp depress panel shutter having extra reinforcement on sides & edges in gel coat finish. the core of the shutter & frame is to be filed up with injected fire retardant grade polyurethene foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium fixtures & fastenings & fastener sleeve., providing and fixing frp frame size 125x65 mm and 35mm thick frp shutter having extra reinforcement on sides & edges in polish finish. the core of the shutter & frame is to be filed up with injected polyurethene foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium s.s fixtures & fastenings & fastener sleeve., providing and fixing frp of 28mm thick fibre glass shutter with 1.5 to 2.0 mm thick fire retardent grade frp skin in depressed panel design having extra reinforcement on sides & edges & in gel coat finish. the core of the shutter is to be filled up with injected retardent grade polyurethane foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof , weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium s.s fixtures & fastenings & fastener sleeve., providing and fixing frp of 35mm thick fiber glass shutter with 1.5 to 2.0 mm thick fire retardent grade frp skin in depressed panel design having extra reinforcement on sides & edges & in gel coat finish. the core of the shutter is to be filled up with injected retardent grade polyurethane foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof , weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium fixtures & fastenings., supply of 35mm thick fiber glass shutter with 1.5 to 2.0 mm thick fire retardent grade frp skin in wood grain rasied panel design having extra reinforcement on sides & edges & in polish design finish. the core of the shutter is to be filled up with injected retardent grade polyurethane foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole shutter is to be water proof , weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium s.s finish fixtures & fastenings., providing and fixing windown shutter of 75x30 mm size with 4mm fully glazed panels with pvc batten main farme size having 1.5 to 2.0 mm thick fire retardent grade frp shutter having extra reinforcement on sides & edges in polish finish. the core of the shutter & frame is to be filed up with injected polyurethene foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. the whole frp frame & shutter is to be water proof weather proof, termite proof & resistance to mild acid / alkali. rates are to be inclusive of s.s hinges with necessary screws & alluminium s.s fixtures & fastenings & fastener sleeve., providing and fixing 30mm thick factory made solid panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15 mm for top and bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture, m.s. frame shall be covered with 5 mm thick heat moulded pvc ‘c’ channel of size 30 x 50 mm forming stiles, and 5mm thick 75mm wide pvc sheets for top rail, lock rail and bottom rail on either side, and 10mm ( 5mm x 2 ) thick, 20mm wide cross pvc sheet as gap insert for top rail and bottom rail, panelling of 5 stiles and rails with 30mm wide x 5mm thick pvc sheet beading on eighter side, and joined together with solvent cement adhesive, . an additional 5mm thick pvc strip of 20mm width is to be stculk on the interior side of the ‘c’ channel using pvc solvent cement adhesive etc. complete as per direction of engineer in charge, manufacture’s specification and drawing., providing and fixing 30mm thick factory made solid both side prelam panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top and bottom rails. m.s. frame shall have a coat of steel primer of approved makde and manufactures. m.s frame covered with 5mm thick heat moulded prelim pvc ‘c’ channel of siz 30mm thickness, 70 mm width of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles, and 5mm thick, 95mm wide pream pvc sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side ot form top and bottom rail and 115mm wide prelim pvc sheet out of which 75nmm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rails shall be provided either side of the panel. 10mm ( 5mm x 2 ) thick 20mm wide cross pvc sheet shall be provided as gap insert for top rail and bottom rails. panelling of 5mm thck both side prelim pvc sheet to be fitted in the m.s. frame welded, sealed to the stiles and rails with 7mm ( 5mm + 2 mm ) thick x 15mm wide pvc sheet beading on inner side, and joined togeth with solvent cement adhesive. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the ‘c†chanel using pvc solvent adhesive etc. complete as per direction of engineering in charge, manufacture’s specification and rawing., providing and fixing 30mm thick factory made solid single side prelam panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thckness and size of 19mm x 19mm for stiles, and 15mm x 15mm for top and bottom rails. the m.s. frame shall have coat of steel primers of approved makde and manufacture. the m.s. frame shall be covered with 5mm thick heat moulded single side prelim pvc ‘c’ channel of size 30 x 50mm to form stiles and 5mm thick and 75mm wide single side prelim pvc sheets shallbe for the top, bttom and lock rails. paneling of 5mm thick one side prelim sheet to be fitted in the m.s. frame and sealed to the front ( prelam side ) stiles and rails ( which should have a 5mm 45 degree bent portion as beading ) and attached to the back ( white / lvory ) stiles and rails ( which should have a 10mm 90 degree bent portion as beading ) using 2 nos. 15mm wide x 5mm thick pvc sheet beading inside the 9 degree bent beading. all stiles, rails and beading to be joined to the panel using solvent cement. an additional 5mm thick pvc strip of 20mm width is to be struck on the interior side of the ‘c’ channel using pvc solvent adhesive and 10mm thick ( 5mm x 20 ) thick 20mm width cross pvc sheet to be fitted as gap insert for top and bottom rails, etc. complete as per direction of engineer in charge, manufacture’s specification and drawing., providing and fixing 30mm thick factor made fully glazed solid pvc door shutter consisting of frame made out of m.s. tube of 19m gauge thickness and size of 19mm x 19mm for styles and 15mm x 15mm for top, lock and bottom rails m.s. frame shall have a coat of steel primer of approved make and manufacture, m.s. frame shall be covered with 5mm thick heat moulded pvc ‘c†channel of size 75mm x 30mm x 50mm out of which 10mm shall be bent at 90 degree towards inner side on front face of the door forming stiles. for top rail and bottom rail, m.s. frame shall be covered with 5mm thick, 100mm wide pvc sheet out of whch 10mm shall be bent of 90 degree towars inner side on front face of the door. m.s. frame at lock rail shall be covered with 125 mm wide pvc sheet out of which 10mm on both the edges shall be bent at 90 degre on front face of the door and 75mm wide pvc sheet shall cover the m.s. frame at top, lock and bottom rail on side of door, 5mm thick 20mm wide cross pvc sheet as gap insert for tp and bottom rail.pvc sheet beading of 15mm thck ( 5mm x 30, 15mm wide to be stuck, internally with solvent cement adhesive in stiles and rails. glass panel will be fitted exernally in the clear space available between the stiles and rails and fixed between pvc sheet of stiles and rails bent at 90 degree on front face and 15mm x 10mm ‘l’ shape outer beading nailed on stiles and rails at the back side. so that the ‘l’ shape pvc beading can be removed when required for replacement of broken glass etc. complete as per direction of engineer in charge and manufacture’s specification., providing and fixing 30mm thick factory made wire guazed solid pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock and bottm rails, m.s. frame shall have a coat of steel primers of approved make and manufacture, 19mm x 19mm m.s. square tubes shall be coveed with 5mm thick head mouled pvc ‘c’ channel of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15 mm shall be bent in 90 degree angle on either side forming stiles and 5mm thick 115mm wide pvc sheet out of which 100mm shal be flat and 15mm shal be betn in 90 degree on the inner side to from top and bottom rails and 130mm wide pvc sheet out of which 100mm shal be flat and 15mm shal be bent in 90 degree on both side to from lock rail 10mm ( 5mm x 2 ) thick, 20mm wide cross pvc sheet as gap insert for top rail and bottom rail, panel will be of g.i. wire gauge of 24 gauge to be fitted in by ‘c’ channel of size 10mm x 35mm on the either side in the stiles.the inner side ‘c’ channel is fixed by 19mm x 19mm m.s. tube on both side with screws. the wire mesh in top, bottom and lock rail is sealed with 15mm x 15mm tube with g.i.wire, 1mm ( 5mmm x 2 ) thick pvc strip of 25mm width is to be stuck and screw on both side of g.i. wire guage interior at the top, bottom and lock rails. an additional 5mm thck pvc strip of 20mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent cement adhesive etc. complete as per dirction of engineer in charge, manufacture’s specification and drawing., providing and fixing 35mm thick factory made moulded door shuter consisting of solid core single leaf flush door of 30mm thickness, lipped with 15mm ( 5mm x 3 ) thick x 30mm width on one stiles and top rail and 10mm ( 5mm x 2 ) thick x 30mm width on the other stiles and bottom rails. the inner panel laminated with 2mm thick termite proof, water proof and fire resistant moulded pvc sheet with 2, 4, 6 raised panel design in different plain and / or prelim colours on one side after routing the moulded design on flush door and 2mm plain and / or prelim pvc sheet on other side using rubber adhesive on flush door and solvent cement adhesive on the pvc liping etc. complete as per direction of engineer in charge, manufacture’s specification and drawing., providing and fixing 30mm thick factory made moulded door shutter wood free consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails, m.s. frame shall have a coat of steel primers. the inner panel shall consist of 25mm thick high density eps conforming to is 4671 1984 bonded with 2mm thick termite proof, water proof and fire resistant moulded pvc sheet with 2, 4, 6 raised panel design in different plain and / or prelim colours after routing the moulded design on one side and 2mm plain and / or prelim pvc sheet on other side of the eps. the edges of panel to be sealed with lipping of 10mm wide pvc sheet batton ( made by sticking 2 pvc rigid foam sheets of 5mm thickness using pvc solvent cement ) and stiles 25mm ( 5mm x 5 ) thick and 30mm width pvc sheet fitted along m.s. tube for lock provision and for lock height 5mm thick pvc sheet of size 150mm x 100mm fixed with upper and lower face of inner side of eps panel etc. complete as per direction of engineer in charge manufacture’s specification and drawing., providing and fixing factory made polyvinyl chioride ( pvc ) door frame of the size 50 x 47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid pvc foam sheet, mitre out of two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm m.s. square tubes. the two vertical door profiles are to be reinforced with 19 x 19 mm m.s. square tube of 19 gauge, epdm rubber gasket weather seal to be provided through out the frame. the door frame shal be fixed to the wall using 65 / 100 mm long m.s. screws through the frame by using pvc fasteners. a miniumum of 4 nos. os screws to be provided for each vertical members and minium 2 nos. for horizontal members etc. complete as per manufactures specification and direction of engineer in charge., providing and fixing of fully glazed solid pvc panel pvc door along with solid pvc door frame. 30mm thick factory made fully glazed solid pvc door shutter consisting of frame made out of m.s. tube of 19 gauge thickness and size of 19mm x 19mm for style and 15mm x 15mm for top, lock and bottom rail. m.s. frame shall have a coat of steel primer of approved make and manufacture. m.s. frame shall be covered with 5 mm thick heat mouled pvc ‘c†channel of size 75mm x 30mm x 50mm out of whch 10mm shall be bent at 90 degree towards inner side on front face of the door. m.s. frame at lock rail shall be covered with 125 mm wide pvc sheet out of which 0mm on both the edges shall be bent at 90 degree on front face of the door and 7mm wide pvc sheet shall cover the m.s. frame at top, lock and bottom rail on back side of door, 5 mm thick 20mm wide cross pvc sheet as gap insert for top and bottom rail. pvc sheet beading of 15mm thick ( 5mm x3 ) 15mm wide to be stuck internally with solvent cement adhesive in stiles and rails. glass panel will be fittd externally in the clear space available between the stiles and rails and fixed between pvc sheet of stiles and rails bent at 90 degree on front face and 15mm x 10mm ‘l shape outer beading nailed on stiles and rails at the back side. so tha the ‘l’ shape pvc beading can be removed when required for replacement of broken glass etc. complete as per direction of engineer in charge and manufactuture’s specification, providing and fixing complete sliding shutter solid pvc window 25mm thick factory made glazed solid pvc window shutter consisting of frame made out of m.s. tube of 19 gauge of size 15 x 15mm for styles top, bottom rail. m.s. frame shall have a coat of steel primer of approved make and manufacture, m.s. frame shall be covered with 4mm thick heat mouled pvc ‘c’ channel of size 58mm x 25mm x 38 mm out of which 8mm shall be bent at 90 degree towards inner side on front face of the window shutter forming stiles. for top rail and bottom rails, m>s. frame shall be covered with 4mm thick, 58mm wide pvc sheet out of which 8mm shall be bent at 90 degree towards inner side on front face and 38mm wide pvc sheet shall cover the m.s. frame at top and bottom rail on back side of window shutter, 4mm thick 15mm wide cross pvc sheet as gap insert for top and bottom rail. pvc sheet beading of 8mm thick ( 4mm x 2 ) to be stuck internally with solvent cement adhesive in top and bottom rails. glass panel will be fitted externally in the clear space available between stiles & rails and fixed between pvc sheet of stiles and rails bent at 90 degree on front face 12mm x 123mm ‘l’ shape outer pvc beading nailed on stiles and rails at the back side so that ‘l’ shape outer pvc beading can be removed when required for replacement of broken glass etc. complete as per direction of etc. complete as per direction of engineer in charge and manufactuture’s specification., providing and fixing plain / printed pvc sheet wall paneling of thickness 5mm consisting of panels having size 1220 mm x 2440 mm stuck on inner frame work of 50mm wide strips of 5mm thick pvc sheet. the strips should have in their center a groove of 6mm width and 1mm depth for sinking the head of the screw used to fix the strips to the wall and should be placed vertically at equal intervals of 10†center to center. the pvc strips shall be fixd to the wall using 65mm long m.s. scress through the groove in the strip by using pvc fasteners. the distance between two screws shall not be more than 200 a groove of 2mm may be left at the joint of two panel for aesthetic looks. the exact size of the panel and correspondingly of the grid may vary depending on the size of the wall., providing and fixing prelam pvc sheet wall paneling of thickness 5mm consisting of panels having size 1220 x 2440 mm stuck on inner frame work of 50mm wide strips of 5mm thick pvc sheet. the strips should have in their center a grove of 6mm width asnd 1mm depth for sinking the had of the screw using to fix the strips of the wall and should be placed vertically at equal intervals of 10†center to center. the pvc strips shall be fixed to the wall using 65mm long m.s. scres through the groove in the strip by using pvc fasteners. the distance between two screws shall not be more than 200 mm. a groove of 2mm may be left at the joint of two panel for aesthetic looks. the exact size of the panel and correspondingly of the grid may vary depending on the size of the wall., providing and fixing full height prelam pvc partition system 50mm thick consisting of 40mm sandwich pvc panel made out of 36mm high density expanded polystyrene sheet ( e.p.s. thermocol ) stuck on both side with 2mm thick prelim pvc sheet reinforced with frame work made from 35mm x 5mm m.s. angle. in between two m.s. angles 4 mm with feathered edges shall be fixed on floor and 50 x 75 mm with feathered edges prelim pvc “c†channel of size 50mm x 75mm with feathered edges prelim pvc panel shall be inserted in the pvc ‘c†channel the first and last m.s. angle should be erected such that it is inside a pvc c channel of size 50 x 75mm in between adjoining eps sandwiched pvc partition panel 4mm thick x 75 mm width prelim pvc sheet feathered at edges shall be stuck on front and back face using solvent cement etc. an additional 4mm thick pvc strip of 40mm width is to be stuck on the intrior side of the ‘c†channel using pvc solvent adhesive completeas per direction of engineer in charge. manufacture’s specification and drawing., providing and fixing full height plan / colour pvc partition system 50mm thick consisting of 40mm sandwich pvc panel made out of 36mm high density expanded polystyrene sheet ( e.p.s. thermocol ) stuck on both side with 2mm thick plain pvc sheet reinforced with frame work made from 35mm x 5mm m.s. angle. in between two m.s. angles 4 mm thick plan heat moulded pvc ‘c’ channel of size 50mm x 100 mm with feathered edes shall be fixed on floor and 50 x 75 mm with feathered edges plain / printed / prelim pvc ‘c’ channel shall be fixed in the ceiling. sandwich pvc panel shall be inserted in the pvc “c†channel. the first and last m.s. angle should be erected such that it is inside a pvc c channel of size 50 x 75mm. in between adjoining eps sandwiched pvc partition panel 4mm thick x 75mm width plain pvc sheet feathered at edges shall be stuck on front and back face using solvent cement etc. and additional 4mm thick pvc strip of 40mm width is to be stuck on the interior side of the c channel using pvc solvent adhesive complete as per direction of engineer in charge, manufacture’s specification and drawing., providing and fixing full height printed pvc partition system 50mm thick pvc partition consisting of 40mm sandwich pvc panel made out of 36mm high density expanded polystyred shet ( eps thermocol ) stuck on the both side with 2mm thick printed pvc sheet reinforced with frame work made from 35mm x 5mm m.s. angle. in between two m.s. angles 4mm thick printed heat moulded pvc c channel of size 50mm x 100mm with feathered, edges shall be fixed on floor and 50 x 75 mm with feathered edges printed pvc c channel shall be fixed in the ceiling, sandwich pvc panel shall be inserted in the pvc c channel. the first and last m.s. angle should be erected such that it is inside a pvc c channel of size 50 x 75mm in between adjoining ep sandwiched pvc partition panel 4mm thick x 75mm width printed pvc sheet feathered at edges shall be suck on front and back face using solvent cement. if the height of partition exceeds 8 feet; then 15mm x 30mm m.s. tube is welded horizontally at the joint of panels in between two vertical angels etc. an additional 4mm thick pvc strip of 40mm width is to be stuck on the interior side of the c channel using pvc solvent adhesive complete as per direction of engineer in charge, manufactures., providing and fixing pvc plain colour false ceiing with grid type with alu frame consisting of 600 mm x 600mm 3mm thick plain pvc sheet used as panel insert in a frame work made using anodized alluminium t section of size 1†x 1†( 25 x 25mm, 19 gauge or 1mm thick ) in square pattern of grid sizes of 2 x 2 ( 600 x 600mm ) . the alluminium frame work is supported from the ceiling with the help of g.i. hook and g.i. wire / 6mm m.s. rods of required sizes to maintain proper level etc. the aluminium frame work is supported on side wall with the use of alluminium l section of size 1 x 1 ( 25 x 25mm ) angles et. complete as per direction of engineer in charge. manufactures, specification and drawing, providing and fixing pvc printed pain colour false ceiling with grid type with alluminium frame consisting of 600mm x 600mm 3mm thick plain pvc sheet used as panel insert in a frame work made using anodized alluminium t section of size 1 x 1 ( 235 x 25mm, 19 gauge or 1 mm thick ) in square pattern of grid sizes of 2 x 2 ( 600 x 600mm ) the alluminium frame work is supported from the cceiling with the help of g.i. hook and g.i. wire / 6mm m.s. rods of required sizes to maintain proper level etc. the aluminium frame work is supported on side wall with the use of alluminium l section of size 1 x 1 ( 25 x 25mm ) angles etc. complete as per direction of engineer in charge. manufactures specification and drawing., providing and fixing pvc plain colour false ceiling with flush type with alluminium frame, frame work is done with three different sections of g.i. sheet of 24 gauge thickness named as c, u and l. the c section is fixed with hangers at an equal distance of 36†each and then u section is fixed perpendicular on c section with steel screws at an equal distance of 16†each. the complete frame work is supported by g.i. l angle 6mm rod hangers from the roof and l sections is fixed all around the wall as shown in the diagram. 5mm pvc sheet strips of size 2 wide and fixed with counter sunk steel screw on the u section. further 3mm pvc sheet is stuck to these pvc strips with solvent cement such that joining lines are perfectly matched. p.u. putty is filled, ceiling for getting fine surface finish etc. complete as per direction of engineer in charge, manufacturer’s specification and drawing., providing and fixing pvc printed false ceiling with flush type with alluminium frame, frame work is done with three different sections of g.i. sheet of 24 gauge thickness named as c, u and l. the c section is fixed with hangers at an equal distance of 36†each and then u section is fixed perpendicular on c section with steel screws at and equal distance of 16†each. the complete frame work is supported by g.i. l angle / 6 mm rod hangers from the roof and l sections is fixed all around the wall as shown in the diagram. 5mm pvc sheet strips of size 2 wide are fixd with counter sunk steel screws on the u section. further 3mm pvc sheet is stuck to these pvc strips with solvent cement such that joining lines are perfectly matched. p.u. putty is filled, dried and leveled and requisite coats of primer and paint is done on the ceiling for getting fine surface finish etc. complete as per direction of engineering and charge manufacturer’s specification and drawing, extra rate for using polyester fiber ( 12mm ) with triangular of equivalent cross section with specific gravity 1.35 to 1.40 ( as a secondary reinforcement ) in concrete of any grade at the rate of 125 gms per 50 kg of cement consumption., extra rate for using polyester fiber ( 6mm ) with triangular cross of equivalent section with specific gravity 1.35 to 1.40 ( as a secondary reinforcement ) in mortar of any grade at the rate of 125 gms per 50 kg of cement consumption., providing fusion bonded epoxy coating not less than 175 micron thickness and up to 300 micron to reinforcement bars as per is 13620 1993 / astm 775 m including testing of coating at plant and all taxes ( a ) 10mm to 16mm dia bar, providing fusion bonded epoxy coating not less than 175 micron thickness and up to 300 micron to reinforcement bars as per is 13620 1993 / astm 775 m including testing of coating at plant and all taxes ( b ) 20mm to 32 mm dia bar, steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. ( a ) in beams and joists, channels angles tees, flats, with connecting plates or angle cleats as in main and cross beams. hip and jack rafters, purlins conneted to common rafters and the like, steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. ( d ) in trussses and trussed purlins, upto 25 m. span and 15 m. ovarall height., providing and fixing in position callapsible steel shutters with vertical channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size with top and bottom rails of t_rin 40x 40 x 6 mm with 38mm dia, steel pulleys complete with bolts, nuts, locking arrangements, stoppers handles including applying a priming coat of read lead paint., providing and fixing 1mm thick m.s. sheet sliding shutters with frame and diagonal braces of 40 x 40 x 6 mm angle iron, 3.15 mm m.s. gusset plates at junctions and corners 25 mm dia. pulley, 40 x 40 x 6mm angle and t iron huide rail at top and bottom respactively with handles, stoppers and locking agangement etc, including applying a priming coat of red lead paint., providing and fixing rolling shutters of approved make made of 80 mm wide m.s. laths inter locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arragements for inside and outside locking with push pull operation including the cost of hood cover and spring etc. complete. ( a ) shutters having width below 3.5 m., providing and fixing rolling shutters of approved make made of 80 mm wide m.s. laths inter locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arragements for inside and outside locking with push pull operation including the cost of hood cover and spring etc. complete. ( b ) shutters having width 3.5 m. and above, providing and fixing rolling shutters of approved make made of 80 mm wide m.s. laths inter locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push pull operation complete but excluding the cost of hood cover and spring. ( a ) shutters having width below 3.5.m., providing and fixing rolling shutters of approved make made of 80 mm wide m.s. laths inter locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push pull operation complete but excluding the cost of hood cover and spring. ( b ) shutters havind width above 3.5 m., providing and fixing 27.5 cm. lcng wire spring grade no.2 of approved make for rolling shutters., providing and fixing hood cover for rolling shutters ( a ) shutters having width below 3.5 meters, providing and fixing hood cover for rolling shutters ( b ) shutters having width 3.5 meters and above, fixing standard steel doors, windows and ventilatos inwalls with 16 x 3.15 mm longs 10 cm. long embeded in cement concrete block 15 x 10 x 10 of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate of 20mm size ) cost for supply of door / window / ventilators shall be paid separately., providing and fixing m.s. fan clamps type 1 to 16mm dia m.s. bar bent to shape with hooked ends to r.c.c. slabs curing, laying including painting the exposed portion of loops, all as per standard designe complete, extra over rate of item 20 for providing and fixing m.s. fan clamps type ii as per standard design in r.c.c. beams during laying towards additional height of the clamp due to beam rib., providing and fixing m.s. round holding down or anchor bolts with nuts and washer plates complete., providing and fixing extruded aluminum window having extruded aluminum colour anodized section frame main outer size 127mm x 38.10mm x 1.35mm ( of jindal section no:2443, @ wt.1.384 kg / mt ) , horizontal four track member size 122.20mm x 31.75mm x 1.10mm ( of jindal section no:8787, @ wt. 1.205 kg / mt ) , vertical member of size 122.20mm x 31.75mm x 1.50mm ( of jindal section no:8935, @ wt. 1.398 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing window having extruded aluminum colour anodized section frame main outer size 95mm x 24mm x 1.17mm ( of jindal section no:2459 @ wt.of 0.738 kg / mt ) , horizontal three track member size 92mm x 31.75mm x 1.30mm ( of jindal section no:8688, @ wt.1.07 kg / mt ) , vertical member of size 92mm x 31.75mm x 1.50mm ( of jindal section no:8933, @ wt. 1.06 kg / mt ) with sliding shutters of horizontal member size 40 mmx18mm x1.29mm ( of jindal section no:8947@ wt.of 0.456 kg / mt ) , vertical member of size 40mm x 18mm x 1.29 mm ( of jindal section no:8949 @ wt.of 0.456kg / mt / with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc, providing and fixing window having extruded aluminum colour anodized section frame main outer size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094 kg / rmt ) , horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm ( of jindal section no: 8687 @ wt.of 0.695 kg / mt ) , vertical member of size 61.85 mm x 31.75mm x 1.30 mm ( of jindal section no:8758 @ wt.of 0.0.659 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094kg / rmt with colour anodized alluminium frame with 5 mm thick transparent bronze colour tinted float glass with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for.window, providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm ( jindal section :2434, @ wt. 0.643 kg / mt ) with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for ventilation, providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094kg / rmt with colour anodized alluminium frame with 5 mm thick transparent bronze colour tinted float glass as details etc complete for fix window., providing and fixing extruded aluminum window having extruded aluminum colour powder coated section frame main outer size 127mm x 38.10mm x 1.35mm ( of jindal section no:2443, @ wt.1.384 kg / mt ) , horizontal four track member size 122.20mm x 31.75mm x 1.10mm ( of jindal section no:8787, @ wt. 1.205 kg / mt ) , vertical member of size 122.20mm x 31.75mm x 1.50mm ( of jindal section no:8935, @ wt. 1.398 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing window having extruded aluminum colour powder coated section frame main outer size 95mm x 24mm x 1.17mm ( of jindal section no:2459 @ wt.of 0.738 kg / mt ) , horizontal three track member size 92mm x 31.75mm x 1.30mm ( of jindal section no:8688, @ wt.1.07 kg / mt ) , vertical member of size 92mm x 31.75mm x 1.50mm ( of jindal section no:8933, @ wt. 1.06 kg / mt ) with sliding shutters of horizontal member size 40 mmx18mm x1.29mm ( of jindal section no:8947@ wt.of 0.456 kg / mt ) , vertical member of size 40mm x 18mm x 1.29 mm ( of jindal section no:8949 @ wt.of 0.456kg / mt / with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc, providing and fixing window having extruded aluminum colour powder coated section frame main outer size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094 kg / rmt ) , horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm ( of jindal section no: 8687 @ wt.of 0.695 kg / mt ) , vertical member of size 61.85 mm x 31.75mm x 1.30 mm ( of jindal section no:8758 @ wt.of 0.0.659 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094kg / rmt with colour powder coated alluminium frame with 5 mm thick transparent bronze colour tinted float glass with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for.window, providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm ( jindal section :2434, @ wt. 0.643 kg / mt ) with colour powder coated alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for ventilation, providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm ( of jindal section no:4605, @ wt 1.094kg / rmt with colour powder coated alluminium frame with 5 mm thick transparent bronze colour tinted float glass as details etc complete for fix window., providing and fixing sheet glass, selected quality ( type c ) bedded in putty and fixed with wooden beading including the cost of wooden beadings of first class teakwood and necessary cutting of glass. ( 1 ) 5 mm thick., providing and fixing sheet glass, selected quality ( type c ) bedded in putty and fixed with wooden beading including the cost of wooden beadings of first class teakwood and necessary cutting of glass. ( 2 ) 6 mm thick., providing and fixing rough cast wired glass, 6mm thick bedded in putty and fixed with wooden beading including the cost of wooden beadings of indian teak wood and necessary cutting of glass. ( c ) wired figured glass, providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first class teak wood and necessary cutting of glass. ( 3 ) 3mm thick, providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first class teak wood and necessary cutting of glass. ( 4 ) 4mm thick, extra for using ground glass ( frosted or obscured on one side ) instead of plain glass., deduct for difference in cost of meterials and labour involved in method of glazing if changed in item no. 13 ( a ) front and back puttied and sprigged or fixed with glazing pins, grinding, polishing and rounding of edges of glass or glazing sheets., providing and laying chequered terrazo tiles 22mm thick with marble chips of sizes upto 6mm in floors on 25mm thick bed of lime mortar 1:1.5 ( 1 lime putty : 1.5 coarse sand ) or c.m. 1:6 ( 1 cement :6 coarse sand ) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete. ( a ) light shades using white cement, providing and laying chequered terrazo tiles 22mm thick with marble chips of sizes upto 6mm in floors on 25mm thick bed of lime mortar 1:1.5 ( 1 lime putty : 1.5 coarse sand ) or c.m. 1:6 ( 1 cement : 6 coarse sand ) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete. ( b ) dark shades using ordinary cement, providing and laying chequered terrazo tiles 28mm thick with marble chips of sizes upto 6mm in treads of stairs and staircases in 12mm thick bed of lime mortar 1:1.5 ( 1 lime putty :1.5 coarse sand ) or c.m. 1:6 ( 1 cement : 6 coarse sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete. ( a ) light shades using white cement, providing and laying chequered terrazo tiles 28mm thick with marble chips of sizes upto 6mm in treads of stairs and staircases in 12mm thick bed of lime mortar 1:1.5 ( 1 lime putty :1.5 coarse sand ) or c.m. 1:6 jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete. ( b ) dark shades using ordinary cement, providing and laying white glazed tiles 6mm thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with flush pointing in white cement., providing and laying ceramic tiles 8mm thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with flush pointing in white cement., providing and laying marbo grenite tiles 8 to 10 mm thick , 24 x 24 in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with flush pointing in white cement., providing and laying marbo grenite tiles 8 to 10 mm thick , 36 x 36 in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with flush pointing in white cement., providing and laying white glazed tiles 6mm thick in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand ) and jointed with white cement slurry, providing and layingceramic tiles 6mm thick in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand ) and jointed with white cement slurry, providing and layingmarbo grenite tiles 8 to 10 mm thick , 24 x 24 in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand ) and jointed with white cement slurry, providing and laying marbo grenite tiles 8 to 10 mm thick , in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand ) and jointed with white cement slurry, providing and fixing 50mm internal or external angles of glazed tiles, providing and laying marble stone slab flooring over 20mm ( average ) base of cement mortar 1:6 ( 1 cement : 6 coarse sand ) or l.m. 1:1.5 ( 1 lime putty : 1.5 coarse sand ) laid and jointed with gray cement slurry including rubbing and polishing complete. ( a ) marble slab 25mm thick, providing and laying polished kota stone slab flooring over 20mm ( average ) thick base of cement mortar 1:6 ( 1 cement : 6 coarse sand ) or l.m. 1.1.5 ( 1 lime putty :1.5 coarse sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. ( a ) 25mm thick, providing and laying polished kota stone slab flooring over 20mm ( average ) thick base of cement mortar 1:6 ( 1 cement : 6 coarse sand ) or l.m. 1.1.5 laid over and jointed with grey cement slurry including rubbing and polishing etc. complete. ( b ) 30 mm thick, providing and laying polished kota stone slab 25mm thick in risers of steps, skirting dedo and pillars laid on 10mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete., providing and laying rough chiseled dressed stone flooring over 20mm average thick base of cement mortar 1:5 ( 1 cement : 5 coarse sand ) or l.m. 1:1.5 ( 1 lime putty : 1.5 coarse sand ) including pointing with cement mortar 1:2 ( 1 cement : 2 stone dust ) etc. complete. ( a ) 25mm thick, providing and laying rough chiseled dressed stone flooring over 20mm thick base of cement mortar 1:5 ( 1 cement : 5 coarse sand ) or l.m. 1:1.5 including pointing with cement mortar 1:2 ( 1 cement : 2 stone dust ) etc. complete. ( b ) 40mm thick, providing and laying cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) laid in one layer and finished with a floating coat of neat cement. ( a ) 40mm thick., providing and laying cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) laid in one layer and finished with a floating coat of neat cement. ( b ) 50mm thick., providing and laying cement concrete pavement ( 25mm to 50mm thick ) with 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size ) including finishing with floating coat of neat cement complete., providing and laying precast cement concrete tiles 20mm thick with aggregate of sizes upto 6mm laid on floors, treads of steps and landing on 20mm thick bed of cement mortar 1:6 ( 1 cement : 6 coarse sand ) or l.m. 1:1.5 ( 1 lime putty : 1.5 coarse sand ) jointed with neat cement slurry with pigment to match the shade of tiles complete with precast tiles of ( c ) dark shades using ordinary cement, providing and laying chequered precast cement concrete tiles 22mm thick with aggegate of sizes upto 6mm in floors, treads of steps and landings on 20mm thick bed of c.m. 1:6 ( 1 cement : 6 sand ) or l.m. 1:1.5 ( 1 lime putty : 1.5 coarse sand ) joint with neat cement slurry with pigments to match the shade of the tiles., extra for rubbing & polishing the precast c.c. tiles for flooring sketing deta., providing and laying brick on edge flooring laid dry grouted with c.m. 1:6 ( 1 cement : 6 coarse sand ) including finishing the joints flush curing etc. complete., p & l 24" x 24" vitrified 8 mm thick tile flooring over 20 mm ( average ) base of cement mortar 1:6 ( 1 cement: 6 coarse sand ) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc. complete for dark shade, p & l 24" x 24" vitrified 8 mm thick tile flooring over 20 mm ( average ) base of cement mortar 1:6 ( 1 cement: 6 coarse sand ) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc. complete for antiskit, p & l 24" x 24" vitrified 8 mm thick tile flooring over 20 mm ( average ) base of cement mortar 1:6 ( 1 cement: 6 coarse sand ) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc. complete for light shade, providing and fixing pre cast concrete kerb stone of gray cement based concrete block 30cm length, 30cm height and 15cm thick of m250 grade concret as per approved design and including excavation for fixing in proper line and level, filling the joint with c:m 1:3 ( 1cement:3fine sand ) etc complete., providing and fixing pre cast concrete kerb stone of gray cement based concrete block 30cm length, 30cm height and 15cm thick of m250 grade concret as per approved design and including excavation for fixing in proper line and level, filling the joint with c:m 1:3 ( 1cement:3fine sand ) etc complete., providing and fixing pre cast rubber dye inter locking concrete block 60mm thick with grade of concrete m200 pnumatic compressed by mechanically pressed and as per approved design including 75mm sand layer for levelling and filling the joint with sand in proper line and level etc complete., providing and fixing pre cast rubber dye inter locking concrete block 60mm thick with grade of concrete m250 pnumatic compressed by mechanically pressed and as per approved design including 75mm sand layer for levelling and filling the joint with sand in proper line and level etc complete., providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall, clearing with water and oxalic acid etc. as directed., providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 ( 1 cement : 3 coarse sand ) & jointed with white cement slurry., providing corrugated g.i. sheet of class 3 roofing fixed with glavanished iron j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washer or g.i. limpet washer. filled with white lead complete excluding the cost of purlins, rafters and trusses. ( 1 ) 0.80 mm thick sheet., providing ridges or hips 600 mm overall in plain g.i. sheet class 3 fixed with g.i.j. or l hooks and nuts 8mm dia g.i. limpet and bitumen washer complete. ( 1 ) 0.80 mm thick sheet., providing valleys 900mm overall in plain 1.6mm thick g.i. sheet fixed with g.i. j or l hooks, bolts and nuts glavanised iron j or l hooks bolts and nuts 8mm dia g.i. limpet and bitumen washers complete., providing asbestos cement sheets roofing fixed with g.i j or l hooks, bolts & nuts 8mm dia. c.i. plain and bitumen washer complete excluding the cost of purlins, fagters and trusses. ( a ) corrugated sheet ( i ) 7mm thick, providing asbestos cement sheets roofing fixed with g.i j or l hooks, bolts and nuts 8mm dia. c.i. plain and bitumen washer complete excluding the cost of purlins, fagters and trusses. ( a ) corrugated sheet ( ii ) 6mm thick, providing and fixing 150mm wide 450mm over all semicircular plain g.i.sheet class 3 gutter with iron brackets 40mm x 3mm size bolts, nuts, washers etc. including making necessary connection with rain water pipes ( i ) 0.80 mm thick sheet., filling cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12.5 mm nominal size ) in gaps of a.c. sheet corrugation and wings of ridges., providing and fixing tiles roofing with manglore tiles including teak reepers of sizes 50mm x 25mm., providing and fixing 6 mm thick lexan polycarbonate multi wall roofing sheet fixed with hilti screw and rubber silicon sealer and alluminium strip of size 50 x 3 mm etc complete as directed by engineer in charge., providing and fixing wooden planks ceiling with tounged and grooved jointing and wood screws ( frame work and cover fillings to be measured and laid for separately ) ( a ) indian teak wood ( i ) 12mm thick, providing and fixing wooden planks ceiling with tounged and grooved jointing and wood screws ( frame work and cover fillings to be measured and laid for separately ) ( a ) indian teak wood ( ii ) 20mm thick, providing and fixing wooden planks ceiling with tounged and grooved jointing and wood screws ( frame work and cover fillings to be measured and laid for separately ) ( a ) indian teak wood ( iii ) 25mm thick, deduct for butt jointing in place of touged and grooved type joint in item no.16.3, providing and fixing fibre insulations board lining with butt jointing and nails ( frame worked cover fillets to be measured and paid for separately ) ( i ) 12mm thick, providing and fixing fibre insulations board lining with butt jointing and nails ( frame worked cover fillets to be measured and paid for separately ) ( ii ) 18mm thick, providing and fixing fibre insulations board lining with butt jointing and nails ( frame worked cover fillets to be measured and paid for separately ) ( iii ) 25mm thick, providing and playwood lining with but jointed and nails ( frame work and cover fillets to be measured and paid for separately ) ( i ) 6mm thick ply., providing and playwood lining with but jointed and nails ( frame work and cover fillets to be measured and paid for separately ) ( ii ) 9mm thick ply., providing and fixing plain asbestos sheet lining with butt jointing and wood screws ( frame work and cover fillets to be paid for separately ) ( i ) class a 6 5mm thick, providing and fixing plain asbestos sheet lining with butt jointing and wood screws ( frame work and cover fillets to be paid for separately ) ( ii ) class b 5 5mm thick, providing and fixing eco friendly light weight calcium silicate false ceiling tiles having tegular edge & 15 mm thick densified edges on the tile periphery for extra strength the light weight calcium silicate ceiling tiles shall have, light reflection 85% non combustible as per b.s. 476 part iv, 100% humidity resistance and also having thermal conductivity 0.043° w / m kc. for the best thermal insulation. the light weight calcium silicate tile shall be of approved texture fine fissured / spintone / cosmos having nrc value of 0.5 & globe having nrc value of 0.75 nrc or equivalent of size 595 x 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections ( galvanizing @120 grams per sqm including both side ) consisting of main ‘t’ runner suitably spaced at joints to get required length and size of 24x38mm made from 0.30 mm thick ( minimum ) sheet, 1200mm centre to centre, and cross ‘t’ of size 24x28mm made out of 0.33mm ( minimum ) sheet spaced 1200mm along spaced between main ‘t’ at 600mm centre to centre to form agrid of 1200x600mm and secondary cross ’t’ of length 600mm and size 24x28mm made of 0.30 mm thick ( minimum ) sheet to be interlocked at middle of the 1200x600mm panel to form grid of size 600x600mm resting on periphery walls / partitions on a perimeter wall angle pre coated steel of size ( 24x24x3000mm made of 0.40mm thick ( minimum ) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edges light weight calcium silicate ceiling tiles of approved texture ( fine fissured / cosmos / spintone ) in the grid including, cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, main ‘t’ runners to be suspended from ceiling using g.i. slotted cleats of size 25x35x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm g.i. adjustable rods with galvanized steel level clips of size 85x30x0.8mm, spaced at 1200mm centre to centre, long main ‘t’ bottom exposed with 24mm of all t sections shall be pre painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer in charge.note: only calcium silicate false ceiling area will be measured from wall to wall. no deduction shall be made for exposed frames / opening ( cut outs ) having area less than 0.30 sqm. the calcium silicate ceiling tiles shall have nrc. value of 0.50 ( minimum ) for fine fissured / spintone / cosmos and 0.75 nrc for globe, light reflection 85% non combustible as per b.s. 476 part iv, 100% humidity resistance and also having thermal conductivity. 0.043° w / m kc.for the best thermal insulation, providing and fixing single layer waterproof gypusm board 12.5 mm thick of the make newgood group co. ltd. or equivalent & newgood group co. ltd. company sections using waterproof board of size 1220 mm x 1830 mm x 8.0 mm suspended by g.i suapender of size 25 mm x 3 mm with intermediate channel of size 18 mm x 40 mm x 0.80 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm center to center and perimetre chanel a of size 20 mm x 27 mm x 30 mm x 0.50 mm at edges & drops including paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat joining compound top coat on ceiling including making necessary opening for light fitting, diffuser etc. complete as per detail drawing as directed., providing 10mm thick cement plaster in single coat on brick / concrete walls for interior plastering upto floor two level and finished even and smooth in ( i ) cement mortar 1:3 ( 1 cement:3 sand ) , providing 10mm thick cement plaster in single coat on brick / concrete walls for interior plastering upto floor two level and finished even and smooth in ( ii ) cement mortar 1:4 ( 1 cement :4 sand ) , providing 10mm thick cement plaster in single coat on brick / concrete walls for interior plastering upto floor two level and finished even and smooth in ( iii ) cement mortar 1:6 ( 1 cement:6 sand ) , providing 15mm thick cement plaster in single coat on rough ( similar ) side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( i ) cement mortar 1:3 ( 1 cement:3 sand ) , providing 15mm thick cement plaster in single coat on rough ( similar ) side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( ii ) cement mortar 1:4 ( 1 cement :4 sand ) , providing 15mm thick cement plaster in single coat on rough ( similar ) side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( iii ) cement mortar 1:6 ( 1 cement:6 sand ) , providing 20mm thick cement plaster in single coat on single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( i ) cement mortar 1:3 ( 1 cement:3 sand ) , providing 20mm thick cement plaster in single coat on single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( ii ) cement mortar 1:4 ( 1 cement :4 sand ) , providing 20mm thick cement plaster in single coat on single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( iii ) cement mortar 1:6 ( 1 cement:6 sand ) , extra over items 58 to 64 for finishing with a floating coat of neat cement slurry., ( a ) extra over items 58 to 67 for providing and mixing water proofing materials in cement mortar in proportion recommended by the manufacturer., extra over items 58 to 71 for plastering on ceilings and sofits of stairs upto floor two level instead of plastering on walls., extra over items 1 to 69, 71 to 87 and 90 for interior plastering above floor two level for every additional storey height. ( 1 ) single coat plaster, extra over items 1 to 69, 71 to 87 and 90 for interior plastering above floor two level for every additional storey height. ( 2 ) two coat plaster, extra over items 1 to 69, 71 to 87 and 90 for interior plastering above floor two level for every additional storey height ( 3 ) floating coat of neat cement, extra over item 91 for plastering on ceiling and soffits of stairs above floor two level for every additional storey height., 20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of c.m. 1:3 ( 1 cement : 3 sand ) and 8mm thick finishing coat of c.m. 1:1 ( 1 cement : 1 sand ) etc. complete., pointing on brickwork with cement mortar 1:3 ( 1 cement : 3 coarse sand ) ( a ) flush pointing, pointing on brickwork with cement mortar 1:3 ( 1 cement : 3 coarse sand ) ( b ) ruled pointing, pointing on brickwork with cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( a ) flush pointing, pointing on brickwork with cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( b ) ruled pointing, extra over item 17.112 to 17.151 for pointing on walls on the outside at height more than 10metres from ground level for every additional height of 5 metres of part there of., providing cement vata ( 10cm. x 10 cm. size ) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete., providing 20 mm thick double coat mala cement plaster on interior brick / concrete work for plastering comprising of base coat of 12 mm thick cement plaster in cement mortar ( 1 cement : 4 coarse sand ) in rough finishing and 8 mm thick top coat of cement mortar 1:2 ( 1 cement : 2 coarse sand ) finished with trovel including scaffolding curing etc. complete., white washing with lime on wall surface ( two coats ) to give an even shade including thoroughly booming the surface to remove all dirt, dust; mortar drops and other foreign matter., white washing with lime on wall surface ( one coats ) to give an even shade including thoroughly booming the surface to remove all dirt, dust; mortar drops and loose scales of lime wash and other foreign matter., extra over items 11 to 12 for every subsequent coat of white washing with lime on wall surface., extra over item 11 for white washing with lime on ceilings and / or sloping roofs., extra over item 2 for white washing with lime on ceilings and sloping roofs., extra over item 13 for every subsequent coat of white washing with lime on ceilings and / or sloping roofs., colour washing with lime on wall surface ( two coats ) over and including a primary coat of white washing to give an even shade after through brooming the surface to remove all dirt, dust, mortar drops and other foreigh matter., colour washing with lime on wall surface ( one coats ) to give an even shade including throughly brooming the surface to loose scales of lime wash and other foreign matter., extra over item 17 to 18 for every subsequent coat of colour wash with lime on wall surface, extra over item 17 for colour washing on ceilings and / or sloping roofs., extra over items 18, 19 for colour washing on ceilings and sloping roofs., cement washing with portland cement slurry on wall surface ( one coat ) to give a smooth finish including thoroughly broomings the surface to remove all dirt, mortar drops and other foreign brand., extra over item no. 29 for every subseqent coat of cement washing with port land cement slurry, distempeing ( two coats ) with oil bound distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth., distempeing ( two coats ) with oil bound washable distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with alkali resistance primer of approved brand after thoroughly brushing the surface and other foreign matter and also including preparing the surface even and sand parpered smooth., distempeing ( one coats ) with oil bound washable distemper of approved brand and of required shade on wall surfaces to give an even shade, after thorouhly brushing the surface clean of all grease dirt, loose pieces of scales and also including distempering with oil bound washable distemper of preparing the surface even and smooth., extra over item 44 to 46 for every subsequent coat of approved brand and manufacture., extra over item 44, 45 for distempering with oil bound washable distemper on celling and sloping roofs., extra over item 46, 47 for every subsequent coat of distempering on celling and sloping roofs., finishing wall with water proofing cement paint of on wall surfaces ( two coats ) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials., extra over item 51 for every subsequent coat of water proofing cement paint of approved brand and manufacture., extra over item 51 for finishing with cement paint on ceiling and sloping roofs., extra over item 53 for every subsequent coat of finishing with cement paint on ceiling and sloping roofs., wall painting ( two coats ) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth., extra over item 57 for every subsequent coat of wall painting with plastic emulsion pain of approved brand., extra over item 57 for painting with plastic emulsion paint of approved brand on ceilings and sloping roofs., extra over item 59 for every subsequent coat of painting with plastic emulsion paint on ceiling and slopping roofs., applying priming coat over new steel and other metel surface after and including preparing the surface by throughly cleaning, oil, grease, dirt and other foreign matter and scoured with brushes fine steel wood, scrapers and sand paper with ready mixed priming paint brushing red lead., painting two coats ( excluding priming coat ) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter., painting one coats ( excluding priming coat ) on previously painted steel and other metal surface with enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter., extra over item 7 and 11 for every subsequent coat of paint, painting two coats ( excluding priming coat ) on new steel and other metal surface with synthetic enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter., painting one coats ( excluding priming coat ) on previously printed steel and other metal surface with synthetic enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter., extra over item 19 and 21 for every subsequent coat of paint., painting two coats ( excluding priming coat ) on external surface of new rain water, soil, waste and vent pipes and fittings with ready mixed bituminous brushing, black, anticorrosive to give an even shade including cleaning of all dirt, dust and other foreign matter. ( b ) 75mm dia., painting two coats ( excluding priming coat ) on external surface of new rain water, soil, waste and vent pipes and fittings with ready mixed bituminous brushing, black, anticorrosive to give an even shade including cleaning of all dirt, dust and other foreign matter. ( c ) 100mm dia., appliying priming coat over new wood and wood based surface after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. ( b ) ready mixed paint brushing wood primier pink., appliying priming coat over new wood and wood based surface after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. ( c ) ready mixed paint brushing priming for enamel, extra over item 59 for every subsequent coat of priming coat. ( b ) ready mixed paint brushing wood primier pink., extra over item 59 for every subsequent coat of priming coat. ( c ) ready mixed paint brushing priming for enamel, painting two coats ( excluding priming coat ) on new wood and wood based surface with enamel paint, interior to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping., painting one coats ( excluding priming coat ) on previously painted wood and wood based surface with enamel paint, to give an even shade including cleaning the of all dirt, dust and other foreign matter., extra over item 71 and 73 for every subsequent coat of paint., painting two coats ( excluding priming coat ) on new wood and wood based surface with ready mixed paint, brushing, oil, gloss, semi gloss to give and even shade including cleaning of all dust, dirt and other foreign matter sand papering and stopping., varnishing two coats ( excluding priming coat ) on new wood and wood based surface under coating with flatting varnish and finished coat with varnish to give an even surface including cleaning the surface of all dirt, dust and sand papering so as to produce a smooth dry surface., extra over item 84 for every subsequent coat of varnish., polishing with french polish on new wood and wood based surface to give an even surface including cleaning, the surface of all dirt, dust and sand papering smooth and including a coat of wood filler., polishing with french polish on previously polished wood and wood based surface to give an even surface including cleaning, the surface of all dirt, dust and sand papered smooth and including a coat of wood filler., appliying wax polish on new wood and wood surface with bees wax polish in proportion of 2:1.5 :1:0.5 ( 2 bees wax : 1.5 linseed oil : 1 turpentine even surface including cleaning the surface of all dirt dust and sand papered smooth., appliying wax polish on previously wax polished wood and wood based surface with bees wax polish in proportion of 2:1.5 :1:0.5 ( 2 bees wax : 1.5 linseed oil : 1 turpentine : 0.5 varnish by weight to give an even surface including cleaning the surface of all dirt dust and sand papered smooth., coat tarring two coats on new wood and wood based surfaces using 0.16 and 0.12 litres of coal tar par sq.m. in the first and second coat respectively to give an even shade including cleaning of all dirt, dust and other foreign matter., extra over item 19.98 or every subsequent coat of painth, writing letter or figures on any surface with black japan paint ( stops, comas, hyphens and the like not to be measured and paid for separately ) ( i ) block ( letters / figures ) ( per 10 letter pet cm.ht ) , writing letter or figures on any surface with black japan paint ( stops, comas, hyphens and the like not to be measured and paid for separately ) ( ii ) indian ( letters / figures ) , extra over items 19.119 for using thick white paint instead of black japan paint. ( i ) block ( letters / figures ) , extra over items 19.119 for using thick white paint instead of black japan paint. ( ii ) indian ( letters / figures ) , painting lines, deashes, arrows, letters etc on roads, air fields and like in two coats with road marking paint, brushing including cleaning the surface of all dirt, dust and other foreign matter. ( i ) over 10cm in width, painting lines, deashes, arrows, letters etc on roads, air fields and like in two coats with road marking paint, brushing including cleaning the surface of all dirt, dust and other foreign matter. ( ii ) upto 10 cm in width, painting lines, deashes, arrows, letters etc on roads, air fields and like in one coats with road marking paint, brushing including cleaning the surface of all dirt, dust and other foreign matter. ( i ) over 10cm in width, painting lines, deashes, arrows, letters etc on roads, air fields and like in one coats with road marking paint, brushing including cleaning the surface of all dirt, dust and other foreign matter. ( ii ) upto 10 cm in width, finishing wall with weather proof exterior emulsion paint on wall surface ( two coats ) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete, applying two coats of birla ( white cement based ) or asian ( acrylic lapy putty ) or equivalent & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth., demolition and disposal of unserviceable materials with all lead and lift. ( i ) lime concrete., demolition and disposal of unserviceable materials with all lead and lift. ( i ) cement concrete., demolition including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( i ) r.c.c. work, demolition of brick work and stone masonry including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( i ) in lime mortar., demolition of brick work and stone masonry including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( ii ) in cement mortar., demolition of terrace including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( i ) brick tile covering., dismentaling tiled of stone floors laid in mortar including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift., dismentaling of wooden floors including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift., dismentaling of sheet roofing including ridges, hips, valleys, gutters etc. stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( i ) g.i.sheet roofing., dismentaling of sheet roofing including ridges, hips, valleys, gutters etc. stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( ii ) a.c. sheet roofing., dismentalings manglore of country tile roofing with battens boarding etc. including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. ( ii ) a.c. sheet roofing., dismentalings cement asbestos hard board in ceiling or partition walls, wooden trellies work including trellies work including frames , stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift., dismentling wood work, wrought framed and fixed in frames trusses including stacking the materials with all lead and lift., dismentling expanded metal or i.r.c fabric with necessary battens and beadings including frame work, and stacking the serviceable materials with all lead and lift., dismentling steel work including distempering and stacking the materials with all lead and lift., dismentling doors, windows, ventilators etc. ( wood or steel ) shutters including chowkhats architraves, holdfasts and other attachment etc. complete and stacking them within all lead and lift. ( i ) not exceeding 3 sq.m. in area., dismentling doors, windows, ventilators etc. ( wood or steel ) shutters including chowkhats architraves, holdfasts and other attachment etc. complete and stacking them within all lead and lift. ( ii ) exceeding 3 sq.m. in area., dismentling barbed wire in fencing including making rolls and also including dismentling fencing posts including all earth work concrete in base and making good the disturbed ground stacking useful materials as directed and disposing as directed and disposing of the unserviceable materials with all lead and lift., dismentling c.i. pipes g.s.w.pipes abd a.c. rain water pipes with fittings and clamps including stacking the materials with all lead and lift ( for any dia, of pipe ) , dismantling santtary fittings like wash basin . w.c. pan indian and european type, flushing tank etc. including stacking the materials with all lead and lift., scraping oil paint from steel and other metal surface and making the surface even ( with hand scraping. ) , providing and fixing 15 mm diameter backup rod having minimum density 22 kg per cum ( astmd 3575 ) & compression strength of 0.40 kg per sqm ( astm 5249 ) and finishing with polysulphide sealant etc. complete. for 12 mm wide expansion joint, providing and fixing 25 mm diameter backup rod having minimum density 22 kg per cum ( astmd 3575 ) & compression strength of 0.40 kg per sqm ( astm 5249 ) and finishing with polysulphide sealant etc. complete. for 20 mm wide expansion joint, providing and fixing 30 mm diameter backup rod having minimum density 22 kg per cum ( astmd 3575 ) & compression strength of 0.40 kg per sqm ( astm 5249 ) and finishing with polysulphide sealant etc. complete. for 25 mm wide expansion joint, providing and fixing 50 mm diameter backup rod having minimum density 22 kg per cum ( astmd 3575 ) & compression strength of 0.40 kg per sqm ( astm 5249 ) and finishing with polysulphide sealant etc. complete. for 40 mm wide expansion joint, providing and fixing 60 mm diameter backup rod having minimum density 22 kg per cum ( astmd 3575 ) & compression strength of 0.40 kg per sqm ( astm 5249 ) and finishing with polysulphide sealant etc. complete. for 50 mm wide expansion joint, removing and scraping of old deteriorated plaster of any thickness fromm wall / r.c.c member including stacking of serviceable material and disposal of unserviceable from site of work with all lead and lift, structural steel work ( confirming to is 4923 1997 ) riveted, bolted or welded in builtup for all type sections, in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per the structural designs and directions of engineer in charge.column ( 122 x 61 x 3.6mm ) , providing and fixing of ridge flashing for roof panel shall be made out of 0.5 mm thick pre coated gi sheet . the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the ridge shall be fixed to the steel members by pop rivet or self drilling / self stitching fastners @ maximum 450 mm c / c along length of capping / flashing etc complete ., providing and fixing of ridge flashing for roof panel shall be made out of 0.5 mm thick pre coated gi sheet. the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the ridge shall be fixed to the steel members by pop rivet or self drilling / self stitching fastners @ maximum 450 mm c / c along length of capping / flashing etc complete., providing and fixing of end cap of roofing panel. the end cap track shall be made out of 0.5 mm thick pre coated gi sheet suitable for 30mm thick panel.the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., providing and fixing of end cap of roofing panel. the end cap track shall be made out of 0.5 mm thick pre coated gi sheet suitable for 40mm thick panel.the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., providing and fixing of corner angle for various flashing in 25mm x 25mm size in equal shape with 5mm edge lipping on both side . the angle flashing shall be made out of 0.5 mm thick pre coated gi sheet with edge bending of approximate 5mm. the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., providing and fixing of corner angle for various flashing in 50mm x 50mm size in equal shape with 5mm edge lipping on both side . the angle flashing shall be made out of 0.5 mm thick pre coated gi sheet with edge bending of approximate 5mm. the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., providing and fixing of corner angle for various flashing in 100mm x 100mm size in equal shape with 5mm edge lipping on both side . the angle flashing shall be made out of 0.5 mm thick pre coated gi sheet with edge bending of approximate 5mm. the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., providing and fixing of corner angle for various flashing in 150mm x 150mm size in equal shape with 5mm edge lipping on both side . the angle flashing shall be made out of 0.5 mm thick pre coated gi sheet with edge bending of approximate 5mm. the precoated sheet shall be of minimum 240 mpa steel grade confirming to is 14246:1995 and shall have zinc coating of minimum 120 gsm as per is:277:1992 , 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 micron. the ppgi sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. the u track shall be fixed with suitable pop rivet with wall and roof panels with minimum spacing of 450 mm c / c., preparing and applying of water soluble, nonflammable, reactive and penetrative silane nanotechnology with water ( <1000 ppm tds ) in the ratio of 1 liter silane :20 liter water mixed with 0.5 liter acrylic copolymer polymer compatible and stable in silane solution. take 1 liter of silane nanotechnology and add in 20 liter water in drum under manual stirring and then add 0.5 liter acrylic copolymer under manual stirring and mix completely. spray apply the solution at the rate of 1 liter per sqm on horizontal and 0.5 liter per sqm on vertical new or old cementitious / concrete surface . ( for very dense concrete of m50 and above for bridges may not absorb 1 liter per sq meter so reduce the water of dilution to 1:10 ) horizonal surface, preparing and applying of water soluble, nonflammable, reactive and penetrative silane nanotechnology with water ( <1000 ppm tds ) in the ratio of 1 liter silane :20 liter water mixed with 0.5 liter acrylic copolymer polymer compatible and stable in silane solution. take 1 liter of silane nanotechnology and add in 20 liter water in drum under manual stirring and then add 0.5 liter acrylic copolymer under manual stirring and mix completely. spray apply the solution at the rate of 1 liter per sqm on horizontal and 0.5 liter per sqm on vertical new or old cementitious / concrete surface . ( for very dense concrete of m50 and above for bridges may not absorb 1 liter per sq meter so reduce the water of dilution to 1:10 ) vertical surface, providing and fixing m.s. fan clamps of shape and size as specified in existing r.c.c. slab including cutting chase and making good., cutting out cracks of roof terrace to v section, cleaning out, wetting, grouting with cement and sand slurry 1:3 ( 1 cement : 3 sand ) , cutting out cracks roof terrace to v section cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand ( 1:1 by weight ) , providing and fixing 1.20 metre high fencing with 2.0 metre long m.s. angle posts 40mm x 40 mm x6 mm and oil painting 3 coats fixed at 2.5 mt, c / c. with five horizontan lines and two diagonals of galvanised steel barbed wire weighting 9.38 kg. per 100 metre, strained and fixed to posts with g.i, staples including fixing the postsin ground with 0.5 m x 0.5.m x 0.5 m. block in c.c1:5:10 etc complete., construction of b, b, masonery paniyara 23cm. x 75cm. wall and 15cm x 15cm curbing including fixing precast r.c.c. arble mosaic ( terrazo ) slab of 75mm thickness on top and smooth finishing in cement plaster in c.m. 1:3 curing etc. complete including drainage out waste water arrangements., constructing a sink ( chowkedi ) with c.c. 1:2:4, 12cm. thick over b.b. masonry in c.m, ( 1:6 ) in front and dwarf wall 1.0 mt.high and 23 cm.thick cement plaster to masonry / in c.m.1:3 ) and cement concrete flooring in 1:2:4: mi x 5 cm. dia. drain pipe etc.complete., constructing a cooking platform 60 cm. width and 70 cm high resting on b.b.masonry walls 23 cm.thick in c.m. ( 1:6 ) with ( i ) fixing or precast r.c.c.1:2:4 ) 8 cm. thick slab with marble chips set in c.m. ( 1:6 ) ( 6mm thick terrazo ) with plastering on exposed faces walls in c.m. ( 1:4 ) etc complete., constructing a cooking platform 60 cm. width and 70 cm high resting on b.b.masonry walls 23 cm.thick in c.m. ( 1:6 ) with ( ii ) fixing black kadappa stone 30mm thick laid on precast r.c.c. ( 1:2:4 ) slab with plastering on exposed faces of wall in c.m. ( 1:4 ) etc complete., carring out timber treatment to all wood work including drilling holes and spraying oil based chemical solution on surface of timber work for termite control including labour and material etc. complete. using chlordene 20 ec. as per 6113_part iii consentration weight 1.00 percent is recommended one litre chemical emulsion dillute with 9 liter of kerosene precent concentration. total dillute concrentration will be 10 litre inclusive of the litre chemical emulsion appication 0.75 / litre chemical per one sqmt printed two coat wood surface., applying general insecticide pest control treatment to floors, cupboards etc including labour material etc. complete. using heptachloride 20 ec. as per 6113_pests consentration weight 0.50 percent is recommended one litre chemical emulsion dillute with 39 liter of water will give. total dillute concrentration will be 40 litre inclusive of one litre chemical emulsion appication 0.5 litre chemical / sqm of surface is recommended as per i.s, carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistment with i.s.i specification. using chlordene and chiorpurfiles 20 ec. as per 6131_paret ii consentration weight one percent is recommended i.e one litre 20 ec chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre chemical emulsion appication at the rate of 5 litre chemical / sqm of surface is recommended as per i.s, carrying out wall treatment for termite control including spraying with chemical solution in oil base ( 0.5 lit. / sq.m. ) including labour and material using hepachlor concentration 20 ec. as per is. 6316_paret ii consentration by weight 0.50 percent is recommended i.e one litre chemical emulsion dillute with 39 liter gof is concrentration total dillite concentration will be 40 litre inclusive of one litre chemical emulsion appication at the rate of 7.5 litre chemical / sqm of surface is recommended as per i.s, providing and laying bilimora type brick facing in c.m. 1:1 laid over bedding of cement mortar 1:3 ( 20mm thickness ) including clearing watering scaffolding etc. complete., providing and fixing teak wook rail of 60mm x 20mm size and 50cm. length including 3 coats of oil paint to wood work with set of 3 pags., providing erecting and fixing double coated syntex pvc. ( isi ) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace., providing and mixing migratory corrosion admixture polyalk cp 293 having specific gravity 1.01 to 1.04, ph value ( minimum 9.50 ) shall be alkaline in nature and having bipolar concrete penetrating corrosion inhibiting properties, inhabitor shall be non nitrite based & have the ability to provide corrosion protection to both anodic and cathodic sites on the steel surface, inhibitor steel complex shall formed polydentate complexes, having more than one bond with steel per molecule of inhibitor, with steel surface to promote proper film formation with enhenced bond to steel, inhibiting the electro chemical corrosion reaction, inhibitor shall not have any adverse effect on concrete compressive strength, inhibitor shall have a corrosion rate of zero coulombs per astm g109 2005, admixture shall be conforming to is 9103 and in liquid form at the rate of 3kg per one cubic meter volume of concrete admixture shall be added to the water, during mixing of cement, sand & aggregates and at the same rate admixture shall be added in case of ready mix concrete at plant site, mixing of admixture during mixing of cement, sand and aggregates or at work site the admixture shall be added in concrete transit mixer before pumping / placing of concrete etc. complete., providing and mixing migratory corrosion admixture polyalk cp 293 having specific gravity 1.01 to 1.04, ph value ( minimum 9.50 ) shall be alkaline in nature and having bipolar concrete penetrating corrosion inhibiting properties, inhabitor shall be non nitrite based & have the ability to provide corrosion protection to both anodic and cathodic sites on the steel surface, inhibitor steel complex shall formed polydentate complexes, having more than one bond with steel per molecule of inhibitor, with steel surface to promote proper film formation with enhenced bond to steel, inhibiting the electro chemical corrosion reaction, inhibitor shall not have any adverse effect on concrete compressive strength, inhibitor shall have a corrosion rate of zero coulombs per astm g109 2005, admixture shall be conforming to is 9103 and in liquid form at the rate of 5% by weight of cementitious materials, during mixing of cement & sand before grouting of cementitious materials etc. complete., providing and fixing resin bonded rock wool of density 48 kg / cum as & where required as directed by engineer in charge. rock wool confirming to is: 8183, providing and fixing vapour breather membrane confirming to ibc 2009 on exterior cement board as & where directed by engineer in charge., providing and laying of one side alluminium foil thermal bubble insulation barrier on the external side of the lwgs wall panel under the cement board as & where directed by engineer in charge., providing and fixing 12 mm thick moisture & fire resistant heavy duty cement fibre board ( high pressure steam cured ) confirming to iso 4862 2000 in wall panels of one face of cold formed galvanised light gauge steel frame structure to form wall / partition as & where directed by engineer in charge, supply & fixing factory finished cold formed light guage steel frame sections confirming to sp:6 ( 5 ) 1980 at site or work including riveted, bolted or welded in builtup for all type of sections , in framed work, cutting, hoisting, fixing in position and applying primer coat of approved steel primer etc. complete as per structural designs & directions of engineer in charge., providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( a ) 15mm, providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( b ) 20mm, providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( c ) 25mm, providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( d ) 32mm, providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( e ) 40mm, providing and fixing to wall, ceiling and floor galvanised mild steel tubes ( medium grade ) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. ( f ) 50mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( a ) 15mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( b ) 20mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( c ) 25mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( d ) 40mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( e ) 65mm, providing and laying in trenches galvanised mild steel tubes ( midium grade ) of the following nominal bore, and tube fitting ( earthwork in trenches to be measured and paid for separately ) ( h ) 80mm, making connection of galvanised mild steel distribution branch with galvanised mild steel main 50mm to 80mm nominal bore by providing and fixing tee including cutting and threading the pipes complete., providing and fixing to wall ceiling and floor 6.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( a ) 20mm, providing and fixing to wall ceiling and floor 6.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( b ) 25mm, providing and fixing to wall ceiling and floor 10.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( c ) 32mm, providing and fixing to wall ceiling and floor 10.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( d ) 40mm, providing and fixing to wall ceiling and floor 10.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( e ) 50mm, providing and fixing to wall ceiling and floor 10.0 kg. f / cm2 working pressure polythene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( f ) 75mm, providing and fixing to wall ceiling and floor 10.0 kg. f / cm2 working pressure poluthene pipes of the following outside dia. low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor ( g ) 110 mm, providing and fixing cast iron spigot and socket soil, waste and ventilating pipes of the following nominal size. ( b ) 75mm dia., providing and fixing cast iron spigot and socket soil, waste and ventilating pipes of the following nominal size. ( c ) 100mm dia., providing and fixing in position cowel went to pipes. ( b ) 75mm dia., providing and fixing in position cowel went to pipes. ( c ) 100mm dia, providing and fixing cast iron ( spun ) nahni trap of the following nominal diameter of self cleaning design with c.i. screaed down or higned grating including cost of cutting and making good the walls and floor 100mm inlet and 50mm outlet. ( c ) 100mm dia., providing and fixing water closet squatting pan ( indian type w.c. pan ) size 580mm ( earthwork, bed concrete, foot reste and trap to be measured and paid for separately ) ( a ) vitreous china. ( i ) long pattern = white colour, providing and fixing wsh down water closet ( european type, w.c. pan ) with integral p or s trap including jointing the trap with soil pipe in cement mortar 1:1 ( 1 cement : 1 fine sand ) ( seal and cover to be measured and paid for separately ) ( a ) vitreous china pattern : ( i ) in white colour, providing and fixing 100mm size p or s trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement mortar 1:1 ( 1 cement : 1 fine sand ) ( a ) vitreous china., providing and fixing in cement mortar 1:3 ( 1 cement : 3 coarse sand ) a, pair of white vitreous china 250mm x 130mm x 30mm footrest to long pattern squatting pan water closet., providing and fixing 12.5 litres low level flushing cistern with a pair, of c.i. or mild brackets, complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with polythene float, c.p brass handle unions and couplings for connections, with inlet, outlet and overflow pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the same connecting the flush bend with cistern and closet ( overflow pipe to be measured and paid for separately ) ( a ) vitreous china ( i ) in white colour, providing and fixing 12.5 litres high level c..i. flushing cistern with a pair of c.i. or mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever g.i. china ( 60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same ( overflow pipe to be measured and paid fo separately ) , providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors., providing and fixing g.i. inlet connection for flush pipe with w.c. pan, providing and fixing plastic seat and cover for wash down water closer with c.p. brass hinges and rubber buffers. ( b ) black plastic seal and cover., providing and fixing washbasin with single hole for pillar tap with c.i. or m.s. brackets painted white including sutting holes and making good the same but excluding fittings. ( a ) vitreous china: ( ii ) flat back washbasin 550 mm x v 400mm size. ( i ) in white colour., providing and fixing kitchen sink with c.i. or m.s. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. ( c ) vitreous china sink. ( i ) 600mm x 450mm x 150mm size, providing and fixing c.p. brass waste for washbasin or sink. ( a ) 32mmdia., providing and fixing c.p. brass waste for washbasin or sink. ( b ) 40mm dia., providing and fixing m.i. fisher union for washbasin or sink. ( a ) 32mm dia., providing and fixing m.i. fisher union for washbasin or sink. ( b ) 40mm dia., providing and fixing 100mm sand cast iron grating for gully, floor or nahni trap., providing and fixing c.p. brass shower rose with 15mm or 20mm inlet. ( a ) 100mm dia. each, providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick a.c. sheet or plywood sheet and fixing to wooden pluge with c.p. brass screws and washers., providing and fixing c.p. brass towel rail comlete with c.p. brass brackets fixed to wooden plugs with c.p. brass scews. ( b ) 600mm x 20mm size., providing and fixing 600mm x 120mm glass shelf with c.p. brass bracket and guard rail complete mixed to wooden plug with c.p. brass screws., providing and fixing toilet paper holder. ( a ) c.p. brass, providing and fixing screw down bib taps of following size. ( a ) brass screw down bib tap polished bright. ( i ) 15mm dia., providing and fixing screw down bib taps of following size. ( a ) brass screw down bib tap polished bright. ( ii ) 20mm dia., providing and fixing screw down bib taps of following size. ( b ) brass chromium plated screws down bib tap. ( i ) 15mm dia., providing and fixing screw down bib taps of following size. ( b ) brass chromium plated screws down bib tap. ( ii ) 20mm dia., providing and fixing screw down bib taps of following size. ( c ) gun metal screw down bib tap. ( i ) 15mm dia., providing and fixing screw down bib taps of following size. ( c ) gun metal screw down bib tap. ( ii ) 20mm dia., providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. ( i ) 15mm dia., providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. ( ii ) 20mm dia., providing and fixing brass screw down stop tap. ( a ) 15mm dia., providing and fixing brass screw down stop tap. ( b ) 20mm dia., providing and fixing brass screw down stop tap. ( c ) 25mm dia., providing and fixing gun metal check or non return fullway wheel valve. ( a ) 15mm dia., providing and fixing gun metal check or non return fullway wheel valve. ( b ) 20mm dia., providing and fixing gun metal check or non return fullway wheel valve. ( c ) 25mm dia., providing and fixing gun metal check or non return fullway wheel valve. ( d ) 32mm dia., providing and fixing gun metal check or non return fullway wheel valve. ( e ) 40mm dia., providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete. ( i ) 20mm dia., providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete. ( ii ) 25mm dia., providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete. ( iii ) 32mm dia., providing and fixing urinal or approved quality including conecting the urinal with waste pipe , tap etc. complete. ( a ) white earthenware flat back or corner type size 430mm x 260mm x 350mm., providing and fixing urinal of approved quality including connection with trap and with integral longitudinal flush pipe. ( a ) squating plate pattern white earthenware 550mm x 300mm., providing and fixing rubber plug for sink or wash basin., providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin., providing and fixing ball cock of approved. quality as directed. ( a ) copper metal ( i ) 25mm dia., providing and fixing ball cock of approved. quality as directed. ( a ) copper metal ( ii ) 50mm dia., providing and fixing ball cock of approved. quality as directed. ( b ) abonite ( i ) 25mm dia., providing and fixing ball cock of approved. quality as directed. ( b ) abonite ( ii ) 50mm dia., providing and fixing c.i. manhole cover 0.60 m. x 0.45m. size having weight not less than 35kg., providing and fixing g.i. rain water spout of 50mm dia. and 30cm. length., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ a ] 15 mm., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ b ] 20 mm., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ c ] 25 mm., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ d ] 32mm., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ e ] 40mm., providing and fixing concealed center point to wall ceiling & floor cpvc ( sdr 13.5 ) pipe having national sanitation foundation ( nsf ) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [ f ] 50mm., providing laying and jointing in true line and level 15mm dia. u.p.v.c. pipe ( sch 40 ) for cold water including fittings make prince / supreme / astral / finolex or equivalent as approved by engineer in charge. pipe shall be fixed on the wall with the help of clamp at every two metre c / c or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials., providing laying and jointing in true line and level 25mm dia. u.p.v.c. pipe ( sch 40 ) for cold water including fittings make prince / supreme / astral / finolex or equivalent as approved by engineer in charge. pipe shall be fixed on the wall with the help of clamp at every two metre c / c or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials., providing laying and jointing in true line and level 32mm dia. u.p.v.c. pipe ( sch 40 ) for cold water including fittings make prince / supreme / astral / finolex or equivalent as approved by engineer in charge. pipe shall be fixed on the wall with the help of clamp at every two metre c / c or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials., providing laying and jointing in true line and level 40mm dia. u.p.v.c. pipe ( sch 40 ) for cold water including fittings make prince / supreme / astral / finolex or equivalent as approved by engineer in charge. pipe shall be fixed on the wall with the help of clamp at every two metre c / c or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials., providing laying and jointing in true line and level 50mm dia. u.p.v.c. pipe ( sch 40 ) for cold water including fittings make prince / supreme / astral / finolex or equivalent as approved by engineer in charge. pipe shall be fixed on the wall with the help of clamp at every two metre c / c or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials., providing, laying and jointing in true line and level 160 diametre u.p.v.c ( type b ) conforming to is 13592 1992 with one end plain and other end socketed with rubber ring, & fittings conforming to isi 14735 1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of pvc clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials., providing, laying and jointing in true line and level 110 diametre u.p.v.c ( type b ) conforming to is 13592 1992 with one end plain and other end socketed with rubber ring, & fittings conforming to isi 14735 1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of pvc clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials., providing and fixing pvc swr nahni trap is 14735 for drain 100 mm diameter with jali of the following nominal diameter of self cleansing design with c.i scread down or hinged grating including the cost of cutting and making good the walls., providing and fixing pvc swr nahni trap is 14735 for drain 75 mm diameter with jali of the following nominal diameter of self cleansing design with c.i scread down or hinged grating including the cost of cutting and making good the walls., providing and laying ( to level or slopes ) and jointing with stiff mixture of cement mortar in proportion 1:1 selt glazed stoneware pipes including testing of pipes and joints complete. ( a ) 100mm dia., providing and laying ( to level or slopes ) and jointing with stiff mixture of cement mortar in proportion 1:1 selt glazed stoneware pipes including testing of pipes and joints complete. ( b ) 150mm dia., providing and laying cement concrete 1:5:10 ( 1 cement : 5 fine sand :10 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete. ( a ) 100 mm dia. ( 112 mm ave.bed thickness ) , providing and laying cement concrete 1:5:10 ( 1 cement : 5 fine sand :10 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete. ( b ) 150mm dia. ( 166mm ave. bed thickness ) , providing and laying lime concrete 1:2:4 ( 1 lime putty :2 fine samd : 4 graded brick aggregates 40mm nominal size ) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete. ( a ) 100 mm dia. 300mm width ( 112 mm ave.bed thickness ) , providing and laying lime concrete 1:2:4 ( 1 lime putty :2 fine samd : 4 graded brick aggregates 40mm nominal size ) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete. ( b ) 150mm dia. 450mm width ( 166mm ave. bed thickness ) , extra over item 24.1 for providing salt glazed stoneware fittings. ( i ) bends of required degree ( any redious ) of following nominal diameters. ( a ) 100mm dia., extra over item 24.1 for providing salt glazed stoneware fittings. ( i ) bends of required degree ( any redious ) of following nominal diameters. ( b ) 150mm dia., extra over item 24.1 for providing salt glazed stoneware fittings. ( ii ) taper bend of required degree of following internal diameters. ( a ) 100mm x 150mm, extra over item 24.1 for providing salt glazed stoneware fittings. ( iii ) single junction of required angle of following internal diametrs. ( a ) 100mm., extra over item 24.1 for providing salt glazed stoneware fittings. ( iii ) single junction of required angle of following internal diametrs. ( b ) 150mm., providing and laying jointing and pointing with stiff mixture of cement mortar 1:1 ( 1 cement : 1 fine sand ) 150 mm internal diameter salt glazed stoneware half round channels., providing and fixing s.w. gully trap with c.i. grating brick masonry chamber and water tight c.i. cover with frame of 300mm x 300mm size ( inside ) with standard weight. ( i ) square mouth traps. ( a ) 100mm x 100mm size p type., providing and fixing s.w. gully trap with c.i. grating brick masonry chamber and water tight c.i. cover with frame of 300mm x 300mm size ( inside ) with standard weight. ( i ) square mouth traps. ( b ) 150mm x 100mm size p or r type, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( b ) 150mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( c ) 250mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( d ) 300mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( e ) 450mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( f ) 500mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( g ) 600mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( h ) 900mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( k ) 1000mm, providing laying ( to level or slopes ) and jointing reinforced concrete light duty non pressure pipes i.s. class np2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. ( m ) 1200mm, constructing manhole with r.c.c. top slab in 1:2:4 mix ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand :6 brick bats 40 + 50mm size ) inside plastering 15mm thick with cement mortar 1:5 ( 1 cement : 5 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ( 1 cement :2 coarse sand :4 stone aggregate 20mm nominal size ) finished smooth complete including curing and festing ( i ) inside size 900mm x 1200mm and 1.5m. deep including c.i. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. ( wt. of cover 64 kg. and wt. of frame 64 kg. ) ( a ) with 230mm thick walls of brick msonry using brick having crushing strength not less than 35kg. / sq.cm. in cement mortar 1:5 ( 1 cement: 5 coarse sand ) ( 1 ) a type depth 0.90 metre for 150mm diameter sewer., constructing manhole with r.c.c. top slab in 1:2:4 mix ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand :6 brick bats 40 + 50mm size ) inside plastering 15mm thick with cement mortar 1:5 ( 1 cement : 5 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ( 1 cement :2 coarse sand :4 stone aggregate 20mm nominal size ) finished smooth complete including curing and festing ( i ) inside size 900mm x 1200mm and 1.5m. deep including c.i. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. ( wt. of cover 64 kg. and wt. of frame 64 kg. ) ( a ) with 230mm thick walls of brick msonry using brick having crushing strength not less than 35kg. / sq.cm. in cement mortar 1:5 ( 1 cement: 5 coarse sand ) ( 2 ) b type depth 1.50 metre for 150mm diameter sewer., constructing manhole with r.c.c. top slab in 1:2:4 mix ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand :6 brick bats 40 + 50mm size ) inside plastering 15mm thick with cement mortar 1:5 ( 1 cement : 5 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ( 1 cement :2 coarse sand :4 stone aggregate 20mm nominal size ) finished smooth complete including curing and festing ( i ) inside size 900mm x 1200mm and 1.5m. deep including c.i. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. ( wt. of cover 64 kg. and wt. of frame 64 kg. ) ( a ) with 230mm thick walls of brick msonry using brick having crushing strength not less than 35kg. / sq.cm. in cement mortar 1:5 ( 1 cement: 5 coarse sand ) ( 3 ) c type depth 2.25 metre for 150mm diameter sewer., ( a ) with 230mm thick walls of brick msonry using brick having crushing strength not less than 35kg. / sq.cm. in cement mortar 1:5 ( 1 cement: 5 coarse sand ) ( 4 ) d type depth 3.15 metre for 150mm diameter sewer., ( i ) extra rate for constructing b.b. masonry for every additional depth of 0.1m. or part thereof over item no.24.27 ( i ) for depth from 0.9m to 1.5m., ( ii ) extra rate for constructing b.b. masonry for every additional depth of 0.1m. gr part thereof over item no.24.27 ( i ) for depth from 1.50m. to 2.25m., ( iii ) extra rate for constructing b.b. masonry for every additional depth of 0.1m. or part thereof over item no. 24.27 ( iii ) for depth from 2.25m to 3.15m., ( iv ) extra rate for constructing b.b. masonry for every additional depth of 0.1m. or part thereof over item no. 24.27 ( iv ) for depth above 3.15m., providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of anti corrosive paint etc. complete., supplying and fixing c.i. cover 300mm x 300mm without frame for gulley trap ( standard pattern ) te weight of cover to be not less 4.53 kg. ) , providing and erecting at the site of work steel ventilating column of 150m internal diameter and 12.20 metre high from g.l. to bottom of top grill including c.i. grill and base plate bolts and nuts etc. and excavation in foundation of size 120cm. x 120vcm. x 165cm. and filling the pit with first layer of cement concrete 1:3:6 mix ( 1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size ) of 120cm. x 120cm. x 90cm. and remaining pit with b.b.c. 1:3:6 mix ( 1 cement :3 coarse sand:6 brickbats 40+50mm size ) and providing fillet in cement concrete 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm. nominal size ) at g.l. and 3 coats of silver paint etc. complete., constructing brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm c.i. horizontal grating wih frame complete., constructing brick masonry road gully chamber 450mm x 450mm x 775mm with vertical gating complete., constructing brick masonry road gully chamber 1100mm x 775mm including 500mm x 450mm ( c.i. horizontal grating with frame and vertical grating complete. ) , constructing brick masonry chamber for underground c.i. inspection chamber and bends with briocks having croshing strength not less than 35kg. cm2 in c.m. 1:5 c.i. cover with frame ( light duty ) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38kg. ( wt. of cover 23 kg. ) and wt. of frame 15kg. ) ( r.c.c. top slabe with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm size ) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete. ( i ) inside dimensions 455mmx 610mm and 450mm deep for single pipe line., constructing brick masonry chamber for underground c.i. inspection chamber and bends with briocks having croshing strength not less than 35kg. cm2 in c.m. 1:5 c.i. cover with frame ( light duty ) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38kg. ( wt. of cover 23 kg. ) and wt. of frame 15kg. ) ( r.c.c. top slabe with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm size ) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete. ( ii ) inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets., constructing brick masonry chamber for underground c.i. inspection chamber and bends with briocks having croshing strength not less than 35kg. cm2 in c.m. 1:5 c.i. cover with frame ( light duty ) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38kg. ( wt. of cover 23 kg. ) and wt. of frame 15kg. ) ( r.c.c. top slabe with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm size ) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete. ( iii ) inside dimensions 600mm x mm and 450mm deep for pipe lines with three or more inlets., extra over items 24.44 for every additional depth of 0.1m. of part thereof beyond 450mm depth for brick masonry chamber. ( i ) for 455mm x 610mm size., extra over items 24.44 for every additional depth of 0.1m. of part thereof beyond 450mm depth for brick masonry chamber. ( ii ) for 500mm x 700mm size., extra over items 24.44 for every additional depth of 0.1m. of part thereof beyond 450mm depth for brick masonry chamber. ( iii ) for 600mm x 850mm size., ( a ) providing sock pit of 2.00 cu.m. volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in c.m. 1:3 with finishing curing etc. complete as directed., ( b ) providing sock pit of 5.00 cu.m. volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in c.m. 1:3 with finishing curing etc. complete as directed., providing and fixing single layer waterproof gypusm board 8 mm thick of the make newgood group co. ltd. or equivalent & newgood group co. ltd. company sections using waterproof board of size 1220 mm x 1830 mm x 8.0 mm suspended by g.i suapender of size 25 mm x 3 mm with intermediate channel of size 18 mm x 40 mm x 0.80 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm center to center and perimetre chanel a of size 20 mm x 27 mm x 30 mm x 0.50 mm at edges & drops including paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat joining compound top coat on ceiling including making necessary opening for light fitting, diffuser etc. complete as per detail drawing as directed., providing and laying ordinary cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggr. 20mm nominal size ) and curing etc. complete including the cost of formwork but excluding the cost of reinforcement for cornise for all heights., providing m 200 controlled cement concrete road using trimix vaccum dewatering system with mixing conplast p 211 ( water reduction concrete admixture ) @ 100 ml per bag of cement with mixing of recon 3s fibers ( reliance product ) at 125 gms per bag of cement with providing and fixing & removing of "c" channel having 75 x 75 mm as per required level slope and thickness of concrete and leveling and finishing the concrete using surface vibrator, power floater and trowel light brooming on as directed including making expansion joint of size 20 x 200 mm & filling the expansion joint using colpar 200 as per manufactures specitions by cutting of joint using concrete cutter machine etc. complete., providing and laying ordinary cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggr. 20mm nominal size ) with curing etc. complete including the cost of form work in coping and plinth protection., providing and laying cement concrete 1:1:2 ( 1 cement : 1 coarse sand : 2 graded stone aggregate 20mm nominal size ) and curing complete including cost of formwork & excluding cost of reinforcement for reinforcement concrete work in ( a ) foundation, footing, base of column & mass concrete., providing and laying cement concrete 1:1:2 ( 1 cement : 1 coarse sand : 2 graded stone aggregate 20mm nominal size ) and curing complete including cost of formwork & excluding cost of reinforcement for reinforcement concrete work in column, pillars, posts, strats upto floor two level., providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size ) and curing complete including cost of form work and excluding cost of reinforcement for reinforced cement concrete work in plinth beam, providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size ) and curing complete including cost of form work and excluding cost of reinforcement for reinforced cement concrete work in rcc wall upto floor two level., providing and laying cement concrete 1:1:2 and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in ( a ) foundations, footings bases of columns and the like and mass concrete & pile work, providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size ) and curing complete including cost of form work and excluding cost of reinforcement for reinforced cement concrete work in column, providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size ) and curing complete including cost of form work and excluding cost of reinforcement for reinforced cement concrete work in beam, providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size ) and curing complete including cost of form work and excluding cost of reinforcement for reinforced cement concrete work in slab, providing and fixing cup board with teakwood frame size 75mm x 25mm with 25mm thick termite proof commercial plywood isi mark quality including the cost of 1mm thick lamination sheet on outer side & 0.80mm thick lamination sheet on inside fixtures and fastenig and locking arrangment of approved quality including polishing to exposed surface etc. complete as per detailed drawing and instruction of engineer in charge., providing and fixng decorative ceiling using 6mm e board self designing pattern of approved design with framing grid 60mm x 60mm of alluminium plain pipe of 40mm x 25mm x 1.00mm suspended ceiling with runners in lengthwise and widthwise with alluminium angle screw and making grooves in required pattern including anchoring and supported to purlins soffits as per required of cement and applying 2 ( two ) coats plastice emulsion paint to give and even shade of approved brand & decorative ceiling lights with all necessary matrials and labour etc. complete., providing and fixing single shutter alluminium anodized openable window of frame 63mm x 25mm x 1.00mm size having top & vertical shutters of size 38 x 18 x 1.50mm & bottom shutter of size 50 x 18 x 1.50mm including using glazing patta, glazing clip, rubber gasket, locking arrangement, handles with 5mm thick plain glass etc. complete., renovation for existing 35mm thick teak wood paneled shutter using 6mm thick commercial plywood on both side and fixing approved 1mm thick laminated sheet on both side with all labour and material including fixtures and fastening of best quality etc. complete., providing and fixing anodised alluminium partition for cabin with 63.5mm x 38mm x 1.5mm ( door shutter should be paid seperately ) and fixing 9mm thick prelaminated nova board & 5mm thick modi guard plain glass incluidng providing and fixing glazing clip, hathi rubber including cost of labour etc. complete as directed., providing and fixing only alluminium door shutters in new partition with shutter frame, vertical & top members @ size 47.62mm x 44.45mm x 1.38mm & middle member @ size 49.91mm x 44.45mm x 1.24mm and bottom members @ size 114.30mm x 44.45mm x 1.20mm having standard weight with 5mm thick selected quality ( modi guard ) plain glass and 9mm thick prelaminated nova board ( bison panel ) with necessary door closer, door lock and fixtures & fastenings including rubber bedding clips etc. complete as directed., providing and fixing openable alluminium anodized window shutter of size 38mm x 18mm x 1.50mm including using s.s. hinges, screws, stopper and pavan kadi with 5mm thick plain glass, rubber gasket locking arrangement and rollet etc. complete., providing & fixing in position standard extruded aluminum four track ( 20 mm series ) sliding shutters with colour anodized section having outer frame 127 x 38.10 x 1.35mm ( of jindal section no.2443 @ wt. 1.384 kg / mt ) horizontal member size 122.20 x 31.75 x 1.10 mm ( of jindal section no:8787, @ wt. 1.205 kg / mt ) , vertical member of size 122.20mm x 31.75mm x 1.50mm ( of jindal section no:8935, @ wt. 1.398 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window and providing and fixing 30mm wirenet of stainless steel wire of is gauge designation 85 g with wire of 0 56 mm diameter including all required materials labours and equipments as per detailed drwg. as directed., providing & fixing in position standard extruded aluminum three track ( 20 mm series ) sliding shutters with colour anodized section having outer frame 95 x 24 x 1.17mm ( of jindal section no:2459 @ wt.of 0.738 kg / mt ) , horizontal member size 92mm x 31.75mm x 1.30mm ( of jindal section no:8688, @ wt.1.07 kg / mt ) , vertical member of size 92mm x 31.75mm x 1.50mm ( of jindal section no:8933, @ wt. 1.06 kg / mt ) with sliding shutters of horizontal member size 40 mmx18mm x1.29mm ( of jindal section no:8947@ wt.of 0.456 kg / mt ) , vertical member of size 40mm x 18mm x 1.29 mm ( of jindal section no:8949 @ wt.of 0.456kg / mt / with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc. and providing and fixing 30mm wirenet of stainless steel wire of is gauge designation 85 g with wire of 0 56 mm diameter including all required materials labours and equipments as per detailed drwg. as directed., providing & fixing in position standard extruded aluminum four track ( 20 mm series ) sliding shutters with colour anodized section having horizontal member size 122.20 x 31.75 x 1.10 mm ( of jindal section no:8787, @ wt. 1.205 kg / mt ) , vertical member of size 122.20mm x 31.75mm x 1.50mm ( of jindal section no:8935, @ wt. 1.398 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window and providing and fixing 30mm wirenet of stainless steel wire of is gauge designation 85 g with wire of 0 56 mm diameter including all required materials labours and equipments as per detailed drwg. as directed., providing & fixing in position standard extruded aluminum three track ( 20 mm series ) sliding shutters with colour anodized section having horizontal member size 92mm x 31.75mm x 1.30mm ( of jindal section no:8688, @ wt.1.07 kg / mt ) , vertical member of size 92mm x 31.75mm x 1.50mm ( of jindal section no:8933, @ wt. 1.06 kg / mt ) with sliding shutters of horizontal member size 40 mmx18mm x1.29mm ( of jindal section no:8947@ wt.of 0.456 kg / mt ) , vertical member of size 40mm x 18mm x 1.29 mm ( of jindal section no:8949 @ wt.of 0.456kg / mt / with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc. and providing and fixing 30mm wirenet of stainless steel wire of is gauge designation 85 g with wire of 0 56 mm diameter including all required materials labours and equipments as per detailed drwg. as directed., providing and fixing extruded aluminum four track window having extruded aluminum colour anodized section frame main horizontal member size 122.20 x 31.75 x 1.10 mm ( of jindal section no:8787, @ wt. 1.205 kg / mt ) , vertical member of size 122.20mm x 31.75mm x 1.50mm ( of jindal section no:8935, @ wt. 1.398 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing window having extruded aluminum three track colour anodized section frame main horizontal member size 92mm x 31.75mm x 1.30mm ( of jindal section no:8688, @ wt.1.07 kg / mt ) , vertical member of size 92mm x 31.75mm x 1.50mm ( of jindal section no:8933, @ wt. 1.06 kg / mt ) with sliding shutters of horizontal member size 40 mmx18mm x1.29mm ( of jindal section no:8947@ wt.of 0.456 kg / mt ) , vertical member of size 40mm x 18mm x 1.29 mm ( of jindal section no:8949 @ wt.of 0.456kg / mt / with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc., providing and fixing window having extruded aluminum two track colour anodized section frame main horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm ( of jindal section no: 8687 @ wt.of 0.695 kg / mt ) , vertical member of size 61.85 mm x 31.75mm x 1.30 mm ( of jindal section no:8758 @ wt.of 0.0.659 kg / mt ) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm ( of jindal section no:8949 @ wt.of 0.456kg / mt ) , vertical member of size 40mm x 18mm x 1.29mm ( of jindal section no:8947 @ wt.of 0.456kg / mt / section 8948, @ wt. 0.457 kg / mt ) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for window., providing and fixing colour anodized alluminium blade strip frame for ventilation with 5 mm thick frosted glass louvers as details etc complete for ventilation, providing and fixing ms iron compound gate including using the frame of g.i. pipe 40mm dia ( medium grade ) and using 12mm square bar at 7.50 cms c / c including painting two coats with one coat of priming coat including fixture and fastening ( i.e. aldrop, narmada khunta, long stopper etc. ) welding charges and fixing etc. complete., providing and making m.s. door frame of size 40mm x 40mm x 5mm & shutter size with 30mm x 30mm x 5mm including 1.80mm thick 16 guage m.s. plate with neccessary welding, cutting, fixing, holdfast & oil paint etc. complete., providing frp sheets roofing ( 1.5mm thick ) fixed with galvanised iron "j" or "l" hooks bolts and nuts 8 mm diameter with bitumen and g.i. limpet washeres, filled with white lead complete excluding the cost of purlins rafters and trusses ( 1 ) 1.50 mm thick sheet., providing and laying 1.20 mt. wide plinth protection with excavatior for foundation up to 0.25 mt depth and 0.35 mt. width and c.c. 1:5:10 brick work in c.m. 1:6 and finished wall with 10mm thicks cement plaster in c.m. 1:4 to brick masonary including chequred tiles flooring, sand filling etc. complete as directed., providing and laying water proofing treatment on terrace including cleaning the surface by wire brush as directed including applying neat cement slurry @ 2.75 kg / sq.smt. mixed with water proofing compound after cleaning the surface, laying cement concrete using brickbats 25 to 100mm size well immersed in water with 50% of cement mortar 1:5 ( 1 cement :5 coarse sabd ) mixed with water proofing compound over 20mm thick layers of cement mortar 1:5 ( 1 cement :5 sand ) to required slope including rounding of junctions of walls and slabs and after two days of proper curing, applying second coat of cement slurry finishing the surface with rate 20mm thick cement mortar 1:4 and china mosaic tiles and finally finishing the surface with white cement slurry and after finishing the whole terrace shall be flooded with water for a period of two weeks., providing and laying water proofing treatment by conventional method including cleaning the slab surface by wire brush as directed including provding first layer of c.m. 1:4 of 40 mm thickness mixed with water proofing compound at rate prescribed by manufacturer, including putting of brick bats of average thickness 40 mm well immerssed in water laid uniformly on first layer of mortar including applying cement slurry @ rate of 0.08 bag / sqm. on fixed layer of brick bats including maintaining necessary slope, in second layer 40 mm thick c.m 1:4 mixed with water proofing compound as directed, including finishing smooth with cement slurry as directed complete., providing and fixing polished 18mm thick green marble stone with flat edge polished of approved quality clading on sill and around the doors / windows / ventilation with offset 20mm thick cement plaster cm ( 1:4 ) and fixing with cement slurry & adhesive including moulding of exposed edges as directed by engineer in charge etc. complete, providing and laying cupboard / kitchen platform shutter by using 25mm x 37mm teakwood frame, 25mm thick approved quality commercial plywood for shutter with 19mm x 3mm teakwood bidden patting, one side 1mm thick good quality laminated sheet and other side 0.80mm laminated sheet work including necessary paint & fixtures and fastenings magnet including all material and labour etc. complete as directed., providing and laying 18mm thick granite ( black ) top platform ( 0.75mt. height ) with sandwich type polished kotah stone as vertical member including polished 25mm thick kotah stone bottom and shelves in cement mortar 1:2 ( 1 cement :2 sand ) including edge champers polishing cutting and labour & polishing over edges etc. complete., providing and laying machine cut free edges machine polished blue kota stone finished treads & riser in single pieces on a bed of 20mm ( average ) thick base of cement mortar 1:6 ( 1 cement :6 coarse sand ) or l.m. 1:1.5 laid over and jointed with grey cement slurry including rubbing and polishing etc. complete, providing 20mm thick water proofing cement plaster in single coat on rough side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in ( 1 ) cement mortar 1:3 ( 1 cement :3 sand ) including finishing with a floating coat of neat cement slurry with adding water proofing materials like p.d. proof as equivalent., providing and laying stone crete plaster outside for all floor to the brick or concrete surface consisting of basecoat of cement plaster 20mm thick in cm 1:3 ( 1 cement : 3 sand ) in rough finish and top coat of average thickness of 10 mm in white cement & gray cement and marble powder mix in proportion of i.e. equal proportion and mix dolomite pure white or colour chips of grade no to required by volume and pigments mixed as specified plaster shall be chiseled as directed with drip mould pattern groves as per approved pattern including scaffolding curing etc complete, providing and fixing marble stone shelf in walls including making gishi on wall and fixing it with cement mortar 1:4 including all necessary and labour etc. complete, providing and fixing green marble stone partition for urinal including making gishi on wall and fixing it with cement mortar 1:4 including all necessary and labour etc. complete., applying priming or base coat over new steel and other metal surface after over and including preparing the surface by thoroughly cleaning oil, grease dirt and other foreign matter and scoured with brushes fine steel wool, scrapers and sand paper including painting two coats of anti corrosive resistance paint on new steel and other metal surface brushing to give an even shade including cleaning the surface of lall dirt, dust and other foreign matters., providing and making 25mm thick polished kotah stone dedo partition and abhrai including making gishi and wall and fixing it with cement mortar jointed with grey cement slurry including rubbing and polishing etc. complete., providing and laying water proofing treatment on terrace slab [ a ] applying one coat of zycosil in distilled water in proportion 1:10 using paint brush or roller or spray equipment [ b ] after two or three days of ezycosil treatment apply diluted zycofil in ration 1:1 on the dry surface by using a paint brush [ c ] after finishing the whole treatment terrace shall be flooded with water for the period of two weeks or as directed by engineer in charge., providing and fixing stainless steel sink 1.00mm thick of size 460mm x 610mm 200mm with c.i. or m.s. bracket including fixing in wall of made in good as directed including providing & fixing c.p. brass waste 32mm dia m.i. fisher union 32mm dia piller tap capstan heal screw down high pressure with screws, shanles and back nuts of 50mm dia including pvc waste pipe and plastic connection etc. complete., providing and fixing 50 mm dia. gun metal check or non return full way wheel valve etc. complete, providing and fixing 80 mm dia. gun metal check or non return full way wheel valve etc. complete., providing and fixing 110mm dia. flange sluice valve including tail piece, nut bolts and all necessary materials & labor etc. complete., providing and fixing 12.5 litres low level flushing cistern with isi mark pvc flush tank including fittings such as connection pipe with 15mm nominal size pvc ball valve with polythelene float push button type union and coupling for connection with inlet, outlet and overflow pipe 32mm dia. making good the same connecting the flush bend with cistern and closed etc. complete ( a ) pvc forthem ( i ) in required colour., providing and fixng curtain using cotton / nylon / semi nylon / valvet / crush cloth ( price rs.175.00 per meter of 1.20 mt. width and backing cloth of rs.75.00 / rmt. ) including necessary hanging attachments like hooks / rings, 20mm ss rod / alluminium channel / socket on rod ends / middle supporting sockets etc. complete ( opening area shall be measured and paid ) , repairing and raising existing brick masonry chamber 0.60 x 0.60 mt. inside dimensions with bricks having crushing stength not less than 35 kg / m2 in c.m. 1:5 heavy duty perforated rcc precast cover 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) inside plaster 15mm thick with c.m. 1:3 with a floating coat of neat cement slurry etc. including dismentalling demolition brick work, rcc work if necessary with all labor & material etc. as directed., repairing and raising existing brick masonry chamber 0.60 x 0.45 mt. inside dimensions with bricks having crushing stength not less than 35 kg / m2 in c.m. 1:5 heavy duty perforated rcc percast cover 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) inside plaster 15mm thick with c.m. 1:3 with a floating coat of neat cement slurry etc. including dismentalling demolition brick work, rcc work if necessary with all labor & material etc. as directed., constructing brick masonry chamber for underground c.i. inspection chamber and bends with briocks having crushing strength not less than 35kg. / cm2 in c.m. 1:5 with heavy duty pre cast r.c.c. frame size 700 x 700 x 125mm with cover size 600 x 600 x 70mm dimensions, r.c.c. top slabe with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm size ) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete ( rcc cover with frame gfrce brand name ) ( chamber size 500 x 700 x 750mm deep ) , repairing and raising existing storm water chamber ( 1.25 x 0.90 mt. inside dimension ) including providing 10cm thick c.c. 1:2:4 r.c.c. slab including raising and repairing to storm water brick masonry chamber with bricks including demolition of disturb masonry with re construction and raising chamber in c.m. 1:5 including providing plastering, rcc top slab with heavy duty pre cast r.c.c. perforated cover with frame with all labor & material etc. as directed., providing and fixing pre cast rcc solid cover with frame size of cover 600 x 600 x 60mm and size of 700 x 700 x 25mm including required reinforcement including fixing on site as directed etc. complete. ( gfrce brand name ) ., repairing the existing ez 7 section fully glazed window including fixing 4mm glass, new handle, pavan kadi, hook & eye, oil paint including remaining & refixing, welding, riveting nut bolting etc. as directed., providing and fixing pre cast rcc solid cover with frame size of cover 600 x 450 x 70mm including required reinforcement including fixing on site as directed etc. complete., providing and fixing pre cast rcc perforated / solid cover with frame size of cover 300 x 300 x 70mm including required reinforcement including fixing on site as directed etc. complete., providing and fixing pre cast rcc perforated / solid cover with frame size of cover 300 x 450 x 70mm including required reinforcement including fixing on site as directed etc. complete., supplying teakwood of best quality as per size given by engineer in charge., reparing doors, windows & ventilator shutters ( panalled / flush / partly panalled & partly glazed ) including removing shutter, necessary replacement of hinges, megnet, stoppers, handles, aldrop, tadi as required including one coat of primer as directed etc. complete including replacement of broken galsses etc. complete, providing and fixing 90 cm high stainless steel railing made form anticorisive 304 grade ss pipe of 50mm dia. ( 16 guage ) as hand rail with ss 304 grade baluster of 32mm dia. ( 16 guage ) as pertical support fixed in rcc slab at 1.2 mt. c / c including three horizontal ss pipe of 16mm dia. ( 16 guage ) at equal distance fixed by 16mm dia. ( 16 guage ) ss pipe with baluster including accessories as per detailed drawing as directed etc. complete., providing and fixing pop false ceiling fixed with alluminium angle framing of required size with necessary supported including fixing in line & level etc. complete., providing and fixing pvc false ceiling ( 600 x 600mm & 1200 x 600mm moduled size or as size approved by engineer in charge ) ceiling fixeed with alluminium angle framing of required size with necessary supported including fixing in line & level etc. complete., providing and fixing one side 1mm thick laminated 9mm thick commercial plywood sheet wall panelling excluding framing. the colour shade as approved by architect and as directed by engineer in charge with all labour and material., providing and fixing super sil metal gs panel 0.5mm thick ( 600 x 600mm & 1200 x 600mm moduled size or as size approved by engineer in charge ) ceiling fixeed with alluminium angle framing of required size with necessary supported including fixing in line & level etc. complete., providing and fixing wall ceiling and floor 6.0 kg. f / cm2 working pressure polythene pipes of the following outside dia. low density, complete with special flange compression type fittings, wall clips etc. including making good the wall ceiling and floor ( b ) 110 mm, providing and and fixing wall ceiling and floor 6.0 kg. f / cm2 working pressure polythene pipes of the following outside dia. low density, complete with special flange compression type fittings, wall clips etc. including making good the wall ceiling and floor. ( b ) 160 mm, providing and and fixing wall ceiling and floor 10 kg. f / cm2 working pressure polythene pipes of the following outside dia. low density, complete with special flange compression type fittings, wall clips etc. including making good the wall ceiling and floor. ( b ) 160 mm, providing, laying and jointing in true line and level 75 diametre upvc ( type b ) conforming to is 13592 1992 with one end plain and other end socketed with rubber ring, & fittings conforming to isi 14735 1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of pvc clamp of the size 75 mm diametre x 125 mm length x 100 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials., supply & fixing s.s aldrop 20 cm long of asis 304 grade, supply & fixing s.s aldrop 25 cm long of asis 304 grade, supply & fixing s.s aldrop 30 cm long of asis 304 grade, supply & fixing s.s hooks and eyes 10 cms. length asis 304 grade, supply & fixing s.s hooks and eyes 15 cms. length asis 304 grade, supply & fixing s.s hooks and eyes 20 cms. length asis 304 grade, supply & fixing s.s stopper 60 cm long of asis 304 grade, supply & fixing s.s stopper 30 cm long of asis 304 grade, supply & fixing s.s stopper 20 cm long of asis 304 grade, supply & fixing s.s handle for door / window 10 cm size of asis 304 grade, supply & fixing s.s handle for door / window 15 cm size of asis 304 grade, supply & fixing s.s pipe handle 30 cm long of asis 316 grade, supply and fixinglatch ( tadi ) as per sample approved sectional flats ( heavy ) c.p. brass 20 cms. length, supply and fixinglatch ( tadi ) as per sample approved sectional flats ( heavy ) c.p. brass 25 cms. length, supply and fixinglatch ( tadi ) as per sample approved sectional flats ( heavy ) c.p. brass 30 cms. length, supply and fixing mortice lock of standard quality., supply and fixing floor spiring of approved quality inox make or as directed., supply and fixing door closer of ( heavy quality ) hyper or as directed., providing and fixing wash down water closet ( european type wc pan wall hung ) of size 570 x 380 x 400mm with integral p and s trap, flushing system seat cover etc. complete unit of american standard model no.3906 brand or any equivalent quality and brand as approved by engineer in charge including installing and fitting as per manufactures standards by skilled trained workman including testing etc. complete., providing & fixing branded mirror 6mm thick of size 3 x 2 with black frame and standard quality of its equivalent as approved by engineer in charge saint gobian / modi guard equivelent quality etc. complete including fixing with ss stud as directed., providing and fixing single lever kna3104 basin mixer with flexible connectors of isi mark plumber or its equivalent brand as directed engineer in charge., providing and fixing single lever kna3101 lb wall mixer with "l" shaped tabular bend set for over head shower of isi mark of plumber or its equivalent brand as directed engineer in charge., providing and fixing angle cock kna 2105 with wall flauge of isi mark of plumber or its equivalent brand as directed engineer in charge, providing and fixing bidet spray ( heath fancet ) ultima utm 1904 with chrome plated 1.00 meter expendable 100cm 130cm flexible metal tube & holder of plumber or its equivalent brand as directed engineer in charge etc. complete., providing and fixing flush value metro pool soft touch rx7104 with dual flow system with round cover plate of 25 mm size of isi mark plumber or its equivalent as directed by engineer in charge., providing and fixing bib cock two way xm 2109 with wall flange of 15mm dia. of isi mark plumber or its equivalent brand as directed etc. complete., providing and fixing bib cock xm 2103 with flange of isi mark plumber or its equivalent brand as directed engineer in charge etc. complete 15mm dia., providing and fixing concealed stop cock ec 0405 of isi mark of plumber or its equivalent brand as directed engineer in charge etc. complete, providing and fixing 2 flow over head shower itp 2221 with antitime jets with shower arm and wall hungs of isi mark plumber or its equivalent brand as directed engineer in charge etc. complete., providing and fixing towel ring round eg 7009 of mark of plumber or its equivalent as directed by engineer in charge etc. complete., providing and fixing toilet paper holder eg 7007 with laid ( cover ) of approved brand of plumber or its equivalent as directed engineer in charge etc. complete., providing and fixing towel rack 450mm ( 18" ) with hook eg 7718 of approved brand of plumber or its equivalent as directed engineer in charge etc. complete., providing and fixing soap dish with metal dish erm 0913 of approved brand of plumber or its equivalent as directed by engineer in charge etc. complete., providing & fixing wooden partition / door including 3 1 / 2" x 2" size ghana teakwood framing as directed including 12 mm thick ply on both sides of green or century make bwr ply confirming to is 710 including both side lamination of 1.0 mm thick of green, broome or equivalent make including necessary drawing including 12 mm thick soft board as directed including tapestry it of approx rs.200 / rmt including necessary ghana teakwood beading & melamine polishing to exposed faces including necessary ss screws, khili, fevicol etc. of suggest brand by engineer in charge including all lead & lift as directed by engineer in charge including all lead & lift as directed by engineer in charge and as per architect drawings etc. complete., providing & fixing table for work station of size as directed of height up to 0.80 mt. or size as directed using 19 mm thick plywood of bwr confirming to is 710 of green or century make, designs & grooves as directed by architectural drawings, lamination of 1.0 mm thick in single or double shade of green, broom or equivalent make of plain or texture finish including necessary keyboard drawer, 3 drawer cabinet of size 21" or as directed, stand for cpu size 10" x 20" or size as directed, necessary ss screws, handles, magnet, hinges, khili, drawer lock of godrej make fevicol etc. of suggested brand by engineer in charge telescopic channel of hetthich, sleek or efficient make, teakwood foot rest of 3 x 2 size or size as directed, necessary teakwood beading of ghana teakwood, melamine polishing to exposed edges, providing cable manager including all cost of material, labours with all lead & lift including inside of drawers & shutters in white laminates of 0.80 mm thick as directed by engineer in charge as per architect drawing etc. complete., providing texture colour using asian paints royal colour or its equivalent make including one coat of primer, applying putty nad sand papering in line and level and applying texture effect using suitable roller or equipment as approvd by archiotect complete as directed., providing and fixing m sera board or its equivalent make board of approved design wall panelling as directed including one coat of primer and two coats of plastic paint as directed., providing and fixing gypsum board panelling including fixing gi / teakwood beding of size 2 1 / 2" x 1" @ 1.0mm c / c with ss screws & fixing gypsum board sheets of 12mm thick of size 1.2 x 1.8m on beading with ss screw including lapi putti & one coat of primer & two coats of plastic paint etc. complete., providing and fixing pvc valve for astral / finolex make or as directed ( a ) 15 mm dia., providing and fixing pvc valve for astral / finolex make or as directed ( b ) 25 mm dia., providing and fixing pvc valve for astral / finolex make or as directed ( c ) 32 mm dia., providing and fixing pvc valve for astral / finolex make or as directed ( d ) 40 mm dia., providing and fixing pvc valve for astral / finolex make or as directed ( e ) 50 mm dia., providing and fixing pvc ball valve ( a ) 15 mm dia., providing and fixing pvc ball valve ( b ) 25 mm dia., providing and fixing brass ball valve ( a ) 15 mm dia., providing and fixing brass ball valve ( b ) 25 mm dia., providing and fixing openwel sub merssible mono block pump set 7.5 hp ( c ) 670 lpm discharge @ 40 mtr. head suitable for 50mm dia. delievery pipe cat.ii crompton, kirloskar, kalama or its equivalent as directed by engineer in charge., providing and fixing openwel sub merssible mono block pump set 5 hp ( c ) 670 lpm discharge @ 40 mtr. head suitable for 50mm dia. delievery pipe cat.ii crompton, kirloskar, kalama or its equivalent as directed by engineer in charge., providing and fixing motor control cubical panel ( direct on line ) ( b ) dol for 7.5 hp. gelco, sun, smudra or its equivalent as directed by engineer in charge., providing and fixing motor control cubical panel ( direct on line ) ( b ) dol for 5 hp. gelco, sun, smudra or its equivalent as directed by engineer in charge., providing and fixing isi mark pvc insulated flat flexible sub mersible copper cable. ( c ) 3 core x 4 sq.mm. finolex or its equivalent as directed by engineer in charge., engaging services of labours male / female for various road and building maintainance works including cleaning jungle cutting and other various type of works as directed by engineer in charge., engaging services of labours for cutting shrurbs, grass on building of any height including cost of helper for maintaining jula. ( item include with cost of two labours ) , engaging services of skilled labours for various road and building maintainance works as directed by engineer in charge., engaging services of i st class carpenter for various type of wood works, windows, shutter etc. complete as directed by engineer in charge., engaging services of wireman for all type of repairing electrification work as directed by engineer in charge., engaging services of plumber for all type of repairing of water supply line at any places & any type of works etc. complete as directed by engineer in charge., engaging services of mason for all type of road & building work at any places & any type of works etc. complete as directed by engineer in charge., engaging services of chokidar for all type of materials & building as directed by engineer in charge., engaging services of painter for all type of color work for all type of stucture as directed by engineer in charge., engaging services of driver for light / heavy vehicle as directed., engaging services of white washer for all type of nature works as directed by engineer in charge., engaging tractor with trolly with hydraulic utilities unloading & operator including oil, lubricantes, diesels etc. complete., engaging excavator ( j.c.b. type ) with operator including oil, lubricantes, diesels etc. complete., engaging truct / dumper, water tanker hydraulic utilities unloading & with operator including oil, lubricantes, diesels etc. complete., engaging tandome power roller ( 8 to 10 tone ) with operator including oil, lubricantes, diesels etc. complete., engaging vibratory roller ( earth vibro ) with operator including oil, lubricantes, diesels etc. complete., full back executive revolving chair of approved brand by engineer in charge., half back revolving chair of upproved brand by engineer in charge., visitors chair with coushion on sit and back as approved by engiener in charge., three seater s.s. airport chair, 2.1 meter length and 0.9 meter width executive table with side credenza along with drawers, 1.8 meter length and 0.9 meter width executive table with side credenza along with drawers, pvc chair of approved brand by engineer in charge., 1.2 meter length and 0.6 meter width computer table with key board tray and drawers, 1.6 meter length and 0.8 meter width cleark table with drawers, 2.1 meter hieght and 0.9 meter width steel cupboard, 2.1 meter hieght and 0.9 meter width wooden cupboard, 2.1 meter hieght and 0.9 meter width steel rack, 1.25 meter hieght and 0.75 meter width steel cupboard, 1.25 meter hieght and 0.75 meter width wooden cupboard...
Tender Value : ₹ Ref. Documents
